Home Forums Discussion Monthly Discussion Guitar Discussion Forum Archive – April, 2003

  • Creator
    Topic
  • #19274
    admin
    Keymaster

    Archive for posts from April, 2003

Viewing 221 reply threads
  • Author
    Replies
    • #45360
      Anonymous
      Guest

      how do i use the gt 3 for effects only so i can use my amp clean and dirty channels?

      • #85503
        Anonymous
        Guest

        : how do i use the gt 3 for effects only so i can use my amp clean and dirty channels? Don’t use ampsims or distortion effects, plug amp effectsend into GT-3 input, GT-3 output into amp effect return.

    • #45361
      Anonymous
      Guest

      sunn mustang bass guitar (black)

      This popular thread has been given its own page : sunn mustang bass guitar (black)

    • #45359
      Anonymous
      Guest

      I can’t seem to get my 6 month old Seagull guitar perfectly tuned. If i’m right on in "E" it’s off in "D". Any suggestions?

      • #89979
        Anonymous
        Guest

        After years of frustration with my S6, it turns out there IS a problem… the fretboard is too long at the nut end; it’s too long between nut and 1st fret! I put a piece of a large paper clip under the strings near the nut and with a little adjustment on treble side (about 1/8 inch)…problem solved!!!!

      • #85498
        Anonymous
        Guest

        : I can’t seem to get my 6 month old Seagull guitar perfectly tuned. If i’m right on in "E" it’s off in "D". Any suggestions? As James B said your intonation is probably out. But I would say don’t take it to the tech do it yourself, it’s easy. DO NOT atempt this without a good tuner Fist tune the open bottom "E" string, then play a harmonic at the 12th fret ( to play a harmonic just touch the string ABOVE the 12th fret with any finger on your left hand. Your finger MUST be over the 12th fret, NOT behind it or infront. DO NOT PRESS THE STING DOWN ONTO THE FRET BOARD! Just touch the string gently and pick it this will sound quite a high note. There sould be a cross head screw at the back of your bride, get a screwdriver and turn the scew in or out to tune in the harmonic to your tuner( you should see the bride saddle move slightly) Then retune the open string, repeat the process til both the open string and the 12th fret harmonic read the same on the tuner. Repeat process on all strings, then go back to the "E" and start again this should be the answer to your problems Anymore problems Email me. Stebzy

        • #89985
          Anonymous
          Guest

          After years of frustration with my Seagull S6 I’ve discovered there really IS a problem! The fretboard is too long at the nut end; it’s too long between the nut and 1st fret. I put a length of large paper clip under all six strings near the nut. With a little adjustment on the treble side (about 1/8 inch) problem solved!!!!

        • #107562
          Anonymous
          Guest

          dude, have u changed your guitar strings since u bought it?thats the problem

      • #85531
        Anonymous
        Guest

        : I can’t seem to get my 6 month old Seagull guitar perfectly tuned. If i’m right on in "E" it’s off in "D". Any suggestions? Have your bridge saddles adjusted for intonation by your local tech. Also, make sure your action isn’t set so high that you pull the strings as you fret them. A lot of things can cause tuning problems, but they are all easy fixes if you have a good tech.

    • #45358
      Anonymous
      Guest

      PLEASE ANYONE?

      • #116014
        Anonymous
        Guest

        Hi I have a Vox Phantom available for sale in mint cond Vox Case.. see following link: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=3718324560

      • #85296
        Anonymous
        Guest

        i have a pre 70’s VOX electric 12 string in mint condition. any offers ?

      • #82599
        Anonymous
        Guest

        I sell Vox guitars, basses, parts, etc, as well as Rickenbacker guitars and basses. http://www.rhoadsmusic.com

      • #80096
        Anonymous
        Guest

        : PLEASE ANYONE?I HAVE A 60’S VOX 12 STRING FOR SALE "FOLK TWELVE ELECTRIC" CLASSIC FOLK STYLE/LOOK

      • #113767
        Anonymous
        Guest

        : PLEASE ANYONE? 1964 Apollo Bass – very good condition, with rectangle hard shell case – US$ 1,000.00

      • #96926
        Anonymous
        Guest

        : i have a vox guitar organ for sale.very rare in mint condition,..not nany made…….anybody interested please drop me a line for full detalis and photos

      • #93320
        Anonymous
        Guest

        i have a custom 25 one piece,,,email me on [email protected] the vox has no pickups ,,if anyone can help me find some please email me

      • #91393
        Anonymous
        Guest

        My friend has an early sixties vox meteor in white. it had three single coil pick ups but the neck p.u has been changed for a humbucker at some time. Apart from that it seems to be completely original. He may be interested in selling if the price is right!

        • #92390
          Anonymous
          Guest

          : My friend has an early sixties vox meteor in white. it had three single coil pick ups but the neck p.u has been changed for a humbucker at some time. Apart from that it seems to be completely original. : He may be interested in selling if the price is right!

      • #109278
        Anonymous
        Guest

        : PLEASE ANYONE? hello,,,i have a vox custom 24 that i am selling,,,let me know if you are interested,,,thanks,,,

        • #122573
          Anonymous
          Guest

          : : PLEASE ANYONE? : hello,,,i have a vox custom 24 that i am selling,,,let me know if you are interested,,,thanks,,, If you still have this guitar i might be interested in it. please contact me.

        • #115891
          Anonymous
          Guest

          : : PLEASE ANYONE? : hello,,,i have a vox custom 24 that i am selling,,,let me know if you are interested,,,thanks,,, hey, I have no idea why you would want to sell that guitar but i’m quite interested. Could you send me some pics and a little more info. Thanks.

        • #114361
          Anonymous
          Guest

          : : PLEASE ANYONE? : hello,,,i have a vox custom 24 that i am selling,,,let me know if you are interested,,,thanks,,,

          • #124529
            Anonymous
            Guest

            Have you still got it? Possibly interested….

    • #45357
      Anonymous
      Guest

      I wanted to write a tribute a memorial to my friend shom I help pioneer the first Echosonic Amplifier over 50 years ago. It will be an interestering story I want to tell to the many purchased some of his many inventions over the years. Please send info re this.

      • #107478
        Anonymous
        Guest

        : I wanted to write a tribute a memorial to my friend shom I help pioneer the first Echosonic Amplifier over 50 years ago. It will be an interestering story I want to tell to the many purchased some of his many inventions over the years. Please send info re this. The person is Ray Butts whom I will disclose all information because I was there when it all happened.

    • #45354
      Anonymous
      Guest

      Fender Precision Bass wiring schematics

      This popular thread has been given its own page : Fender Precision Bass wiring schematics

    • #45353
      Anonymous
      Guest

      Squier Strat serial numbers

      This popular thread has been given its own page : Squier Strat serial numbers

    • #45355
      Anonymous
      Guest

      I have a squire strat sunburst which i bought back in about1979/80. All the components are real fenderU.S.A. This came a standard when i got it.. can anyone tell me if this is now classed as a vintage guitar. Its a great player and i am still gigging it to this day. the quality seems a lot better than some of the other strats -(mexican etc). any info would be appreciated. Cheers

      • #85366
        Anonymous
        Guest

        Vintage??? Well…50/50.I’ve owned several of them and thet are good axes.The necks are shaped better than most of the 70’s Strats.These were made in Japan around 1980. The Squires main drawbacks were;1)they still used 3 bolt necks(some 4),(2)they’re only made with alder wood,cheap cuts and(3)I hated the tone of those pickups. But they actually were decent guitars.I don’t think they’re worth more than $350-$450.I still have mine! Hope this helps

    • #45356
      Anonymous
      Guest

      I have a "Tascam" porta studio. When I moved, the power adapter got misplaced somewhere. The back of the machine says that you have to use tascam only. Is this true? or can I just get a 12v adapter elsewhere? I’m really wanting to hook it back up to do some recording. Any input would be appreciated. Thanks in advance. Laurie

      • #96980
        Anonymous
        Guest

        yes, it has to be tascam, im stumbled upon this site thingy here trying to find a 12v tascam adapter, i founf a tascam adapter for a tascam cd player, which should plug into the recorder, but i dunno if its 12v

    • #45352
      Anonymous
      Guest

      Hey guys , How do I tune my acoustic to Nashville tuning ? ……Please respond>>>

      • #114971
        Anonymous
        Guest

        : Hey guys , How do I tune my acoustic to Nashville tuning ? ……Please respond>>> Tune the high E and B strings normally. then get your hands on a set of 12 string guitar strings. Now take the higher octave strings fron g to e and tune them like you would on a 12 string and Voiala. Nashville tuning!

      • #85696
        Anonymous
        Guest

        : Hey guys , How do I tune my acoustic to Nashville tuning ? ……Please respond>>> See: http://www.guitartips.addr.com

    • #45351
      Anonymous
      Guest

      i have downloaded the kazaa and wnmix programs, but dont know how to use them.therefore, i am very unhappy. i love music and want to download to my hearts content.please help this computer dummy thank you!!!

      • #86898
        Anonymous
        Guest

        I HAVE DOWNLOADED KAZAA AND I DONT KNOW HOW TO GET MUSIC ON THERE PLEASE HELP ME

      • #80223
        Anonymous
        Guest

        :I use wnmix at the moment, but have a heard that Kazaa in as good. can anyone give me a bit of feed back about Kazaa, they are requesting $29.95 plus a further$4.95 for unlimited down loads, would this inlcude music and dvd, and on the program side of this are the fairly up to date ie I like to use Adobe photoshop would the latest programs be available.

      • #92869
        Anonymous
        Guest

        i dont know how to download kazaa or wnmix? HELP ME!!!!

      • #89178
        Anonymous
        Guest

        I want to download kazaa but people have told me it will interfere with other things on my computer.

      • #89017
        Anonymous
        Guest

        i know how to use kazaa. but i have heard on the news that it will be a 2500.00 fine and 5 years in prison to download songs from the internet. also the server has to report you. i really love kazaa. is this true? lowwana bigler texas

      • #86172
        Anonymous
        Guest

        : i have downloaded the kazaa and wnmix programs, but dont know how to use them.therefore, i am very unhappy. i love music and want to download to my hearts content.please help this computer dummy thank you!!! on kazza when you boot it up it take a few seconds for it to link up…but on the top of the screen you have your options, search,traffic,my kazza,shared folder…etc….when all the options are in bold letters (not shadowy) then left click on search, type in what your looking for video,audio,image, etc then hit the search button hey presto you have a list of every thing…double left click on the item in the list that you want to download.. go to traffic and it will appear depending if it is on line it will download…. you can download as many as you like at once but this does slow the download time if you have too many running at once…i hope this helps…have fun….

        • #87453
          Anonymous
          Guest

          : : i have downloaded the kazaa and wnmix programs, but dont know how to use them.therefore, i am very unhappy. i love music and want to download to my hearts content.please help this computer dummy thank you!!! : on kazza when you boot it up it take a few seconds for it to link up…but on the top of the screen you have your options, search,traffic,my kazza,shared folder…etc….when all the options are in bold letters (not shadowy) then left click on search, type in what your looking for video,audio,image, etc then hit the search button hey presto you have a list of every thing…double left click on the item in the list that you want to download.. go to traffic and it will appear depending if it is on line it will download…. you can download as many as you like at once but this does slow the download time if you have too many running at once…i hope this helps…have fun….

          • #92277
            Anonymous
            Guest

            I can;t even find wnmix! let alone know how to download it! Help! Anyone got a link?

            • #114042
              Anonymous
              Guest

              go to google.com and type in WinMX and then pick one that says that you want to download it!! 😉

    • #45350
      Anonymous
      Guest

      very intersted in story behind the song wild theme-local hero/ feel in love with this song. this year has been a very spiritual experience for. Please someone give me an idea.

      • #85338
        Anonymous
        Guest

        : very intersted in story behind the song wild theme-local hero/ feel in love with this song. this year has been a very spiritual experience for me. Please someone give me an idea.

    • #45346
      Anonymous
      Guest

      I just bought the above mentioned guitar. I am curious as to the materials in this guitar. Is there a resource site that might give me the info I want if I have the model and serial number?

      • #85518
        Anonymous
        Guest

        : I just bought the above mentioned guitar. I am curious as to the materials in this guitar. Is there a resource site that might give me the info I want if I have the model and serial number? Yes go to http://www.Samick.com they should help you out.

        • #91864
          Anonymous
          Guest

          I have a Samick Bass Artist Series that has a shorted jack. Where can I find the replacement part?

    • #45348
      Anonymous
      Guest

      RP6 Patches

      This popular thread has been given its own page : RP6 Patches

    • #45349
      Anonymous
      Guest

      Ibanez Concord 12 string

      This popular thread has been given its own page : Ibanez Concord 12 string

    • #45347
      Anonymous
      Guest

      Is there anyone who would know the where abouts of a wiring diagram for the guitar mentioned above. Please e-mail mail them to me or post them here. cheers. James

    • #45345
      Anonymous
      Guest

      What do you think the value of this guitar is im the second owner, the original was the 60s – 70s rocker Johny chester, this guitar was backstage at the 60s beatles concert, its a cream 12 string electric with a bigby tremolo, yes its true, whats ya offer? email [email protected]

      • #85320
        Anonymous
        Guest

        : What do you think the value of this guitar is im the second owner, the original was the 60s – 70s rocker Johny chester, this guitar was backstage at the 60s beatles concert, its a cream 12 string electric with a bigby tremolo, yes its true, whats ya offer? email [email protected] >>>> How Much Are Yoy Asking For It Yourself

    • #45344
      Anonymous
      Guest

      want to be more creative and melodic? e mail me for details

    • #45343
      Anonymous
      Guest

      I have a peavey rage 158. This amplifier work good when I put the headphone in it. But when there is no headphone, I heard a sound like putt-putt-putt…. in the speaker. Does anyone can help me?

      • #85494
        Anonymous
        Guest

        : I have a peavey rage 158. This amplifier work good when I put the headphone in it. But when there is no headphone, I heard a sound like putt-putt-putt…. in the speaker. Does anyone can help me? Get the speaker on the amp checked out.

    • #45342
      Anonymous
      Guest

      I was given an old Fender 12 string serial #5690H1270, Got it up and running,,works ok for goofing around,,any info on this guitar(year,original price etc.) would be greatly appreciated.

    • #45340
      Anonymous
      Guest

      I have a important practice tonight and a concert in a couple of days…i have a LTD MH-301 by esp guitar with a floyd rose tremolo on it…i changed the strings today and with the new set of strings my low E string "buzzes" really loud… i tried ajusting the action…nothing…i tried to "re-sattle" the string nothing…i have no idea where the buzzing is comming from…there is nothing loose that vibrates with the vibration of the strings…all the other strings sound perfecly…thanks in advance Miguel

      • #108144
        Anonymous
        Guest

        : I have a important practice tonight and a concert in a couple of days…i have a LTD MH-301 by esp guitar with a floyd rose tremolo on it…i changed the strings today and with the new set of strings my low E string "buzzes" really loud… i tried ajusting the action…nothing…i tried to "re-sattle" the string nothing…i have no idea where the buzzing is comming from…there is nothing loose that vibrates with the vibration of the strings…all the other strings sound perfecly…thanks in advance : Miguel miguel, you either have a saddle piece still buzzing if this happens again. or you have changed string guage size and the neck is not under as much stress which would give you a flatter playability

      • #85491
        Anonymous
        Guest

        : I have a important practice tonight and a concert in a couple of days…i have a LTD MH-301 by esp guitar with a floyd rose tremolo on it…i changed the strings today and with the new set of strings my low E string "buzzes" really loud… i tried ajusting the action…nothing…i tried to "re-sattle" the string nothing…i have no idea where the buzzing is comming from…there is nothing loose that vibrates with the vibration of the strings…all the other strings sound perfecly…thanks in advance : Miguel Check to see if your truss rod is too tight. Fret the low E at the first fret and last fret at the same time. There should be a slight gap (.010 -.020) between the bottom of the srting and the top of the 8th fret. If not, loosen the truss rod nut 1/4 turn and check it again. Also, check that your bridge pickup isn’t too close to the strings. The pickups should be adjusted so that they are about 1/16" below the strings when fretted on the last fret. I hope this helps.

    • #45341
      Anonymous
      Guest

      I have recently been given a Gibson ES347. How much should I insure it for?

      • #98829
        Anonymous
        Guest

        I have a 1978 es-347 ( which happens to be the first year they came out ) which I hav einsured for $2,000.00 based on today’s market .

    • #45339
      Anonymous
      Guest

      Hey, I need some help. I got a Line 6 Spider 2×12 combo and the stock settings that come on the amp really bite. Does anyone have any suggestions that could really help me out? I need the settings for a nice, bright, smooth, clean, a sweet distortion, and a heavy distortion out of the Insane setting, if possible, cause the Insane setting sounds reallly noisy. Please Help!!! Thanks.

      • #93644
        Anonymous
        Guest

        : Hey, I need some help. I got a Line 6 Vetta 2×12 combo and the stock settings that come on the amp really bite. Does anyone have any suggestions that could really help me out? I need the settings for a nice, bright, smooth, clean, a sweet distortion, and a heavy distortion out of the Insane setting, if possible, cause the Insane setting sounds reallly noisy. Please Help!!! Thanks.

      • #108145
        Anonymous
        Guest

        Matt, I have the 1 x 12 combo, but my remarks should apply to that too I think. I like the Spider because live, I have the a channel as clean w some chorus, b is blues, c is hard rodk, and d is hardrock w solo boost, reverb and delay. Just set all the knobs (except master volume) on a channel, then hold in the ‘a’ button on the amp for about 4 seconds, it will blink twice, and Shazaam, you’ve got new settings for channel ‘a.’ You can set all channels this way. I found that I needed to boost the bass eq on all channels to get a sound I liked. The bummer about the Spider is that you can’t tell what the settings are on the amp jsut by looking at it – since all those parameters are pre-programmed. I hope this helps. Also, spend some time with the manual, if you don'[t have one, I[ll bet you can ge3t it off the Line 6 website. regards.

    • #45337
      Anonymous
      Guest

      Who can help? How it look like "The Big Major Square"

    • #45338
      Anonymous
      Guest

      I have a 1982 Deluxe Bullet Fender. I can’t find a bit of information on it anywhere, and would like to know more about it and how much it is worth. If you have any information on it, or need more from me, please contact me. Id really appreciate it.

      • #115211
        Anonymous
        Guest

        the model number is 319.12401001 made in usa has atom sembol if you look close it is SR sears and roebuck what is the yr made

      • #85348
        Anonymous
        Guest

        Check harmony central out

    • #45336
      Anonymous
      Guest

      I have a Martin HJ28. The H is for the herring bone bracing and the J is for Jumbo. It’s an awesome instrument. Does it require any sort of maintenance? I change strings monthly – but am unaware of any periodic TLC it might need. It has no problems that I am aware of. Any knowledgeable replies would be most appreciated!

      • #86306
        Anonymous
        Guest

        : I have a Martin HJ28. The H is for the herring bone bracing and the J is for Jumbo. It’s an awesome instrument. Does it require any sort of maintenance? I change strings monthly – but am unaware of any periodic TLC it might need. It has no problems that I am aware of. Any knowledgeable replies would be most appreciated! occassionly clean the frets with some approved fret polish from a local music store. wipe off any sweat or tesidue with a fine furniture polish and have the truss bar tweeked from time to time to keep the operation of the rod smooth.

    • #45335
      Anonymous
      Guest

      Namaste to all. I am currently shopping for an acoustic guitar amp, price range around $1500Aust. Needed for live performance, have had a play on Some fender models (acoustasonics) and have not been entirely moved enough to buy one for that price. Am playing thru a Roland JC120 at the moment. I want a nice clean "pure" deep wooded sound that i know my guitar has when it’s not plugged in. have only just started my reasearch on Acoustic amps so if anyone has any suggestions that may take me where i need to be it would certainly be appreciated. Thankyou.

      • #107484
        Anonymous
        Guest

        : Namaste to all. : I am currently shopping for an acoustic guitar amp, price range around $1500Aust. Needed for live performance, have had a play on Some fender models (acoustasonics) and have not been entirely moved enough to buy one for that price. Am playing thru a Roland JC120 at the moment. I want a nice clean "pure" deep wooded sound that i know my guitar has when it’s not plugged in. have only just started my reasearch on Acoustic amps so if anyone has any suggestions that may take me where i need to be it would certainly be appreciated. : Thankyou. Hey Bill, I recently bought a Behringer ACX1000. I got it because it offered a warm tube sound as well as an XLR for my vocals. At 300 dollars US I’m thrilled with it and would highly recommend it. As far as output, I can be heard quite nicely when I’m playing alongside an electric guitar amped by a Fender Twin. Happy shopping!

    • #45334
      Anonymous
      Guest

      I have inherited a Glen Campbell Artist Balladeer Anniversary Ovation #1157-7 and I was seeking any information on it. If you know anything on it please let me know Thanks-

      • #85326
        Anonymous
        Guest

        : I have inherited a Glen Campbell Artist Balladeer Anniversary Ovation #1157-7 and I was seeking any information on it. If you know anything on it please let me know : Thanks-

    • #45333
      Anonymous
      Guest

      Help me buy: Cort NTL CE CUSTOM?

      This popular thread has been given its own page : Help me buy: Cort NTL CE CUSTOM?

    • #45332
      Anonymous
      Guest

      I have an original mid 60’s Mosrite bass forsale. It is sunburst with one single coil pickup. Finish is in fair condition (finish checking and some scratches). Neck is in very good condition. Missing the tone control. Electronics work great. Bass sounds incredible. Comes with hardshell case. Email me if you are interested. [email protected]

    • #45331
      Anonymous
      Guest

      yairi 'cbs-masterworks' classical ca. 1971

      This popular thread has been given its own page : yairi ‘cbs-masterworks’ classical ca. 1971

    • #45330
      Anonymous
      Guest

      i need help i built a talkbox and need to know what mic brand to use on it i have a cheap one now but what a good one

    • #45327
      Anonymous
      Guest

      i have a strat which i suspect may have an alien body. there is no traditional recessed input jack on the front; its on the side, like an elite but the hardware isnt gold & pickups & selector are trad. body is tan/brown wood (walnut?) and scratchplate "green". headstock is early smaller size and the front stained a few shades lighter than body. logo is spag, there are two string trees and machines have been replaced by schallers. saddles seem orig. but suspect bridge has been replaced. neck plate is gold (maybe elite?) 4-screw with fender USA on it. anyone help?

    • #45328
      Anonymous
      Guest

      I have an 1969 Ovation solid body electric in good condition. Anyone know what its worth?

      • #112767
        Anonymous
        Guest

        : I have an 1960’S COMMODOR TWIN PICKUP SEMI ACUSTIC SUN BURST RED electric in good condition. Anyone know what its worth?

      • #99324
        Anonymous
        Guest

        I have an old Takamine still in mint condition. It still has the original strings on it. The numbers inside it are EST1962 Japan, and the other number is F-450S-B. Would anyone out there no how much it is worth in Aussie dollars. Cheers

        • #101436
          Anonymous
          Guest

          It probably worth a mint.

      • #88229
        Anonymous
        Guest

        honfer bass similar to beatles time period…

    • #45329
      Anonymous
      Guest

      My father had a martin guitar that is probably 1956-1957. It does have a tiny nick in the body of the guitar, but otherwise is in mint condition. Is there any worth to this guitar The numbers we found on the inside were 000-18 123483. I look forward to hearing from you.

      • #86358
        Anonymous
        Guest

        : My father had a martin guitar that is probably 1956-1957. It does have a tiny nick in the body of the guitar, but otherwise is in mint condition. : Is there any worth to this guitar : The numbers we found on the inside were : 000-18 : 123483. : I look forward to hearing from you. donna: i don’t think you realize what you have. it is worth thousands. do not let anyone or any local music store tell you otherwise and try to buy it for next to nothing. i hope i am not too late in writing this to you. i would not hesitate to tell you that a interested guitar collector would cut off his leg to have this one. he or she would probably offer you upwards to between 5-10 thousand dollars for it depending on the shape it is in

      • #85525
        Anonymous
        Guest

        : My father had a martin guitar that is probably 1956-1957. It does have a tiny nick in the body of the guitar, but otherwise is in mint condition. : Is there any worth to this guitar ummm.. yes, I hate to tell you what it’s worth. Actually, I don’t know for sure but I can find out for you. I do want to caution you about selling it though. You’re likely to find someone who would kill for that guitar so don’t sell it overly cheap!!!! Talk to me at [email protected] Bob : The numbers we found on the inside were : 000-18 : 123483. : I look forward to hearing from you.

        • #124133
          Anonymous
          Guest

          We have a Martin and wondered what it is worth? The numbers on it are.. D-12-20 243901

    • #45326
      Anonymous
      Guest

      I HAVE A 6 STRING BLACKBURST(COLOR) ACOUSTIC GUITAR FOR SALE NOT ASKING FOR TOO MUCH…MAYBE $150…POST OR EMAIL FOR MORE DETAILS…ITS GOING TO COME WITH A HARD SHELL CASE AND A STACK OF TABLUATURE…POSSIBLYY A LEATHER STRAP…LET ME KNOW IF YOUR INTERESTED.

      • #89661
        Anonymous
        Guest

        Is there any possibility this guitar is still for sale? : I HAVE A 6 STRING BLACKBURST(COLOR) ACOUSTIC GUITAR FOR SALE NOT ASKING FOR TOO MUCH…MAYBE $150…POST OR EMAIL FOR MORE DETAILS…ITS GOING TO COME WITH A HARD SHELL CASE AND A STACK OF TABLUATURE…POSSIBLYY A LEATHER STRAP…LET ME KNOW IF YOUR INTERESTED.

      • #89328
        Anonymous
        Guest

        : I HAVE A 6 STRING BLACKBURST(COLOR) ACOUSTIC GUITAR FOR SALE NOT ASKING FOR TOO MUCH…MAYBE $150…POST OR EMAIL FOR MORE DETAILS…ITS GOING TO COME WITH A HARD SHELL CASE AND A STACK OF TABLUATURE…POSSIBLYY A LEATHER STRAP…LET ME KNOW IF YOUR INTERESTED. I am interested let me know where you are. is it possible for me to get a pic o the guitar? how long you have had it?

    • #45325
      Anonymous
      Guest

      Yamaha SG3000 Custom For sale $ Offers. send e-mail for Photo’s

      • #98578
        Anonymous
        Guest

        : Yamaha SG3000 Custom For sale $ Offers. : send e-mail for Photo’s Still for sale? Send Photos Please. Thanks.

        • #115615
          Anonymous
          Guest

          : : Yamaha SG3000 Custom For sale $ Offers. : : send e-mail for Photo’s : Hi, realise I’m a bit late on this one but is still for sale? : Thanks.

    • #45323
      Anonymous
      Guest

      In "King Nothing" by Metallica just before the soft part Jaymz cuts the signal from his guitar. It’s like the pickup just stops working and then comes back. I just want to know how the fuck he did it.

      • #85540
        Anonymous
        Guest

        : In "King Nothing" by Metallica just before the soft part Jaymz cuts the signal from his guitar. It’s like the pickup just stops working and then comes back. I just want to know how the fuck he did it. The only way I know of how this is done, is by fitting a micro switch to your guitar ( a micro switch is what you get in a refridgerator door to turn the light on and off one of these will work just fine)Eddie Van Halen was the first to use one. You can hear him use it on their first album "Van halen one". Track three "You really got me" at the end of the guitar solo. Hope this helps Stebzy

    • #45324
      Anonymous
      Guest

      just bought a used tascam 244- 4 track cassette recorder anyone know where I can get the owner’s manual?

      • #80621
        Anonymous
        Guest

        Did you ever find the owners manual? I need one. Also how much did Tascam 244 cost you? Dom

      • #84004
        Anonymous
        Guest

        I have a manual. Give me an address and I’ll ship you one. Do you know where I can get a rebulid kit for all the rubber and drive belts?

        • #90175
          Anonymous
          Guest

          I am also in need of a tascam 244 manual… i am willing to pay for photocopying services, if only an original is available!

      • #87900
        Anonymous
        Guest

        Also I have bought a 244, I have searched but the owner’s manual seems not to be on the net…

      • #87862
        Anonymous
        Guest

        I also have a tascam 244, and desperatly need a manual, can anywon explain to me via e-mail how to remix tracks using and effects pedel? i was told this can be done, but it doesn’t seem to work?

        • #100271
          Anonymous
          Guest

          I just bought one off of ebay tonight that has the manual included.. If you still need one then email me in about a week after I get it I’ll make and email you a pdf file of it. — [email protected]

          • #100860
            Anonymous
            Guest

            : I just bought one off of ebay tonight that has the manual included.. If you still need one then email me in about a week after I get it I’ll make and email you a pdf file of it. — [email protected]

            • #112499
              Anonymous
              Guest

              : : I just bought one off of ebay tonight that has the manual included.. If you still need one then email me in about a week after I get it I’ll make and email you a pdf file of it. — [email protected] Can I get a copy of that file as I have a portastudio I would love to make it do what it should

            • #122780
              Anonymous
              Guest

              Hi there. I’m also working with a Tascam 244 and desperatly need a manual. If you could mail it to me or let me know of a site where i can get it, i would realy appreciate it. r.

          • #115216
            Anonymous
            Guest

            : I just bought one off of ebay tonight that has the manual included.. If you still need one then email me in about a week after I get it I’ll make and email you a pdf file of it. — [email protected] Could you send me that file too? I’m also looking for that manual.

    • #45322
      Anonymous
      Guest

      So what would you buy? Anybody got any advice (pos or neg) about either of these amps? I can get the Marshall quite cheaply, but I like all the different sounds of the Fender and they’re a bit to "new" for my liking. Anybody?????

      • #85325
        Anonymous
        Guest

        : So what would you buy? This may be old news by now, but I would highly recommend the user reviews on both of these @ harmony-central.com. These reviews are invaluable when shopping for new/used gear. God bless, Stan

        • #88539
          Anonymous
          Guest

          I would go to the store and check them out. Reading "reviews" on Harmony Central doesn’t tell you anything, since everyone will say his amp is 10 points and cool and the best amp in the world. I just got the 6100 and I like the amp very much. I also own a JCM 2000 TSL, which is similar, but this amp can be controlled with a MIDI-device. The Fender can probably also be controlled by MIDI, but is a full digital amp, which is not my cup of tea. Just stick to my advice: try them both with your own guitar in a room at low and high volumes and see what you like best.

    • #45321
      Anonymous
      Guest

      I am trying to find an original Fender 12-string neck for a project guitar. Could be the neck from a Strat XII (electric), or from a Shenandoah or Villager (acoustics), any one of them would do just fine. Thanks!

    • #45320
      Anonymous
      Guest

      I have an old Hohner Les Paul copy. It says Simone on the plate on the head. Is that the model? Also, where can I find the serial number?

      • #107353
        Anonymous
        Guest

        my e-mail addr

    • #45319
      Anonymous
      Guest

      If anyone could help, please do it. I need scores of Paco Pena – ‘Alegrias de Cordoba’ for 6-string guitar. I can change or buy them. Thank you anyway!

    • #45318
      Anonymous
      Guest

      What is the technique for playing dirty? I heard it is going through 2 amps, but don’t know how to hook it up

    • #45316
      Anonymous
      Guest

      Korg A5 effects pedal

      This popular thread has been given its own page : Korg A5 effects pedal

    • #45317
      Anonymous
      Guest

      I want to experiment making my own finger picks but can’t seem to find the plastic I need to work with. Does anyone know of a supplier? Thanks. Greg

    • #45315
      Anonymous
      Guest

      NOW AVAILABLE IN CANADA FOR 1/2 PRICE USA. THESE SUPPORT CUSHIONS FOR CLASSICAL PLAYERS, RELIEVES BACK AND NECK PAIN ASSOCIATED WITH FOOTSTOOLS BY ELIMINATING THEM. AVAILABLE IN LARGE AND SMALL CONTACT [email protected] TO ORDER. PREVENT NERVE DAMAGE AND ENJOY MORE PLAYING WITHOUT THE PAIN FROM FOOTSTOOLS.

      • #107375
        Anonymous
        Guest

        : NOW AVAILABLE IN CANADA FOR 1/2 PRICE USA. THESE SUPPORT CUSHIONS FOR CLASSICAL PLAYERS, RELIEVES BACK AND NECK PAIN ASSOCIATED WITH FOOTSTOOLS BY ELIMINATING THEM. AVAILABLE IN LARGE AND SMALL CONTACT [email protected] TO ORDER. PREVENT NERVE DAMAGE AND ENJOY MORE PLAYING WITHOUT THE PAIN FROM FOOTSTOOLS.

    • #45314
      Anonymous
      Guest

      Can anyone tell me about the origins of this series?

      • #88672
        Anonymous
        Guest

        Does anyone know how to get a manual for as AS 50?

    • #45311
      Anonymous
      Guest

      i need the dementions of a coffin case so i can build one thanx

      • #87600
        Anonymous
        Guest

        : i need the dementions of a coffin case so i can build one thanx I am building one now e mail Me for the demetions.

        • #100145
          Anonymous
          Guest

          : : i also need the dementions of a coffin case so i can build one thanx : I am building one now e mail Me for the demetions.

    • #45312
      Anonymous
      Guest

      I have a tele and love it . I want to duplicate twangy sound used by Brad Pasley,etc.

      • #85341
        Anonymous
        Guest

        In my opinion the best way to "put some fire" into a tele is putting some Joe Barden pick ups on it. You should also have a good nut (graph tech works well) and good bridge saddles (for me old brass Esquire ones are a good choice. Good luck. Keep pickin’

    • #45310
      Anonymous
      Guest

      I was wondering if i should buy a processer or a single effect to start with …i play punk and i have a band started, but my dirty channel on my amp isnt cutting it, so i need some suggestions…also, if u pick one, tell which i should buy and give me some tips. Thanks Josh

      • #107390
        Anonymous
        Guest

        My advice for a Punk-rocker is to use single(durable) pedals.Most punk-rock doesn’t call for a lot of tones.It’s mostly about aggression! I’d say,get a decent dist./OD ,flanger/chorus,delay.If they break,jusy get another one. Could you imagine spending $500. on a processor,just to have some FAT BASTID spill beer on it??? Fucked up,ain’t it?? Good Luck

      • #107361
        Anonymous
        Guest

        To each their own, but I still like the warm sound of pedals.(easier to use too) Check out a Marshall Jackhammer pedal. It has a wide range of distortion sounds for a lot of styles. About $80.00

    • #45313
      Anonymous
      Guest

      Hi, Anyone out there have a nice Yamaki guitar for sale? Thanks, Nick

      • #88048
        Anonymous
        Guest

        : Hi, : Anyone out there have a nice Yamaki guitar for sale? : Thanks, Nick N I have what I believe to be a Yamaki copy of a martin D-35. Sounds great, three piece back with the middle of the back being maple I think and the sides and rest of the back rosewood. Heavy on the inlay around body and soundhole. Does not say Yamaki anywhere on the guitar but I have narrowed it down this far. Am having someone look at it today to help with the I.D. Also has hexagonal inlay on the fretboard. E-mail me if you have any questions. J.

      • #86611
        Anonymous
        Guest

        I have a Yamaki 12-string in good condition. Let me know if you’re interested.

    • #45309
      Anonymous
      Guest

      Does anybody know where I can get the pegs that keep the strings in on my Tanglewood? each time I change the strings one or two pegs snap. does anyone know if there are any other type of pegs rather than plastic ones? Ken

    • #45308
      Anonymous
      Guest

      ehh please im so stupid heh and i wanna know how to make a good punk effect on a korg AX100G thanks

    • #45307
      Anonymous
      Guest

      you can borrow my guitar….

    • #45305
      Anonymous
      Guest

      Does anybody have any lead guitar tablature for JUDAS PRIEST? Or does anyone know where I could get some lead guitar tablature. Please let me know and thank you in advance!! Peace!

      • #88328
        Anonymous
        Guest

        : Does anybody have any lead guitar tablature for JUDAS PRIEST? Or does anyone know where I could get some lead guitar tablature. : Please let me know and thank you in advance!! Peace!

        • #89640
          Anonymous
          Guest

          : : Does anybody have any lead guitar tablature for JUDAS PRIEST? Or does anyone know where I could get some lead guitar tablature. : : Please let me know and thank you in advance!! Peace!

          • #91377
            Anonymous
            Guest

            : : : Does anybody have any lead guitar tablature for JUDAS PRIEST? Or does anyone know where I could get some lead guitar tablature. : : : Please let me know and thank you in advance!! Peace! Judas Priest nesecito la partitura de Hell Patrol si me la mandarian para poder tocarlas grasia pancho [email protected]

    • #45306
      Anonymous
      Guest

      Does anyone want to sell a guitar amp? or distortion pedal maybe a heavy metal one. Please e-mail me. Thank you…Peace!

    • #45304
      Anonymous
      Guest

      I got a new Ibanez PGM guitar, on fret from 1,2,3 the low E string to A,D,G,B, high E string. when I play my guitar with out plug into the amp I heard these buzz noise but when I plug it into the amp I don’t hear NO buzz noise or hear NO dead fret. why do it make that buzz noise ? if you can help me than do email me ! thanks

      • #85046
        Anonymous
        Guest

        If the ‘buzz’ is up the neck (1st fret(s)) it probally isn’t ‘strong’ enough to get picked up, why you hear it unplugged… just dress up the fret if it’s the problem or raise the action a little till it goes away. : I got a new Ibanez PGM guitar, on fret from 1,2,3 the low E string to A,D,G,B, high E string. when I play my guitar with out plug into the amp I heard these buzz noise but when I plug it into the amp I don’t hear NO buzz noise or hear NO dead fret. why do it make that buzz noise ? if you can help me than do email me ! thanks

    • #45303
      Anonymous
      Guest

      can anybody please tell me where i can fin the tab for paul gilberts video guitars from mars 1 classical?

      • #100642
        Anonymous
        Guest

        algunas tablaturas de paul gilbert ?

      • #87775
        Anonymous
        Guest

        im in a hurry, i need the tablature from "king of monsters" from paul gilbert, if anyone can tell me how can i find it i would be very gratefull, thanks

    • #45302
      Anonymous
      Guest

      hello Im Mohammad

      • #85049
        Anonymous
        Guest

        We gonna get all these lame posts like this one !!! : hello : Im Mohammad

    • #45301
      Anonymous
      Guest

      I HAVE A BLACKBURST…VIRGIN…ACOUSTIC AND HARD SHELL CASE FOR SALE!!!NOT ASKING FOR TOO MUCH…REPLY IF INTERESTED OR EMAIL ME…THANKS

    • #45299
      Anonymous
      Guest

      I am looking for some sound advice concerning my choice of acuostic pickups. I have a mid/low end guitar that sound good to me. I also have a great acoustic amp (Roland Brown model). I am looking for a pickup that allows me to play loud with little or no feedback (I can wish can’t I?) and sounds decent. I would like to do this for under 200.00 if possible. Thanks in advance for your advice. Richard

      • #85327
        Anonymous
        Guest

        The undisputed champ for those using acoustic guitars at high spl’s and wanting to avoid feedback is the Sunrise p/u as used by Bono, Leo Kottke, Emmylou Harris, Lyle Lovett and many others. I personally have used mine for almost seven years now. You MUST get the p/u AND the solid state preamp for the "Sunrise" sound. BUT, it will run you about $300.00 – worth every cent. Jim makes 1000 units every year and they go quickly. Check out the Sunrise website for more info. God bless, Stan

    • #45300
      Anonymous
      Guest

      i wonder ? if logic research labs in fullerton,calif. is still around and how might i go about getting my rotoverb fixed? hank

      • #93187
        Anonymous
        Guest

        Hank, I also own a Rotoverb (Logic Research), and mine flaked-out years ago. But it sounded GREAT before it died. I hear the guitar, but I get no rotary action whatsoever. The numbers on the IC chips are too faded for anyone to read. Have you had any luck getting yours repaired? Thanks! Mike : i wonder ? if logic research labs in fullerton,calif. is still around and how might i go about getting my rotoverb fixed? hank

        • #99525
          Anonymous
          Guest

          Also made by Research Labs, it powers up but I get no sound. all 4 footswitches turn on the LEDs. Anybody know where I can get it fixed – in Boston Mass.

        • #96002
          Anonymous
          Guest

          Yes I know a very good tech who fixed perfectly a Rotoverb. But he lives in Italy, so I don’t know if you would send yours over here. The Rotoverb is back to life and it’s on his way to his owner to Texas, right while I am writing.

    • #45298
      Anonymous
      Guest

      I have a guitar from when I was a kid…bought it for 10 bucks. Any thoughts on its market value would be great. Label Reads… Yairi Made in Japan Stamped with the number 270 No. 88 AD 1969 (year made…I got this one) Signed by Saduo Yairi. Thanks for your help!

      • #85077
        Anonymous
        Guest

        I hope I don’t disappoint you but a 30-year old Yairi classical guitar cannot be worth more than $100 today. They are a good student guitar but that’s about it.

        • #101545
          Anonymous
          Guest

          I beg to differ. From my experience both S.Yairi and K.Yairi guitars are considered to be fine quality instruments and a 30yr old one should be worth much more than $100.

    • #45297
      Anonymous
      Guest

      Hi I got a 1978 GB-10 serial number J784387 Head stock production number is 0662 on the inside sticker any Idea what it might be worth ? the guitar is in excellent condition all original.

      • #107377
        Anonymous
        Guest

        Depends if it´s japanese or korean. I have a korean GB-10, don´t know year of made. I guess mi guitar is about 1500 us Dollars A japanese one might be around 1800-2200. Year 1978: i don´t really know if there is something special with that year on that guitar.

        • #110539
          Anonymous
          Guest

          They didn’t make the Korean version of the GB-10 before 1980. Check your serial numbers. the first and the third represent the year. I have a 1981.

    • #45296
      Anonymous
      Guest

      I have a supro with a gumby headstock but the u and p are missing ( it has the capital S and ro. Where would I get a new plastic name Supro with the thunderbolt underneath.

    • #45293
      Anonymous
      Guest

      how do I change the tremmlo system, so that I can use a different string guage, than what it is set for?

      • #85061
        Anonymous
        Guest

        You can use any string gauge you want, just put em on, whats the problem ?? If it has a floyd you’ll just need to readjust the tension and intonation. : how do I change the tremmlo system, so that I can use a different string guage, than what it is set for?

    • #45295
      Anonymous
      Guest

      Incubus patches... Boss gt6

      This popular thread has been given its own page : Incubus patches… Boss gt6

    • #45294
      Anonymous
      Guest

      Dear Sirs: I have in my posession a National lap top steel guitar.It has an ebony top and sides and is a six string. I,ve had it for a number of years now and was wondering who or what company made it and if it has any value as an antique guitar.Hope you can give me some information regarding this little gem.Thankyou. Sincerely Yours Ches Allen

    • #45291
      Anonymous
      Guest

      i need help with my guyatone guitar. i need to know it’s value today, im not sure what year it was made but it’s old

    • #45292
      Anonymous
      Guest

      just had GIVEN to me a really nice guitar which has a unique neck whose neck angle can be adjusted on the fly. had a really nice pro set up on it and it plays like a dream. I have .jpg photos if anyone wants to see it, but my question is how can I date it ? The serial no is model B 407. Any of you guys over in the States help me on this? Also with the guitar were some photos of the guy who owned it and one picture is taken in 1937. Cheers Kevin UK

      • #102561
        Anonymous
        Guest

        Kevin, I also have a paramount guitar from the 30’s. I believe my guitar is from the first year of the Paramount banjo Co. Change over to guitars. The serial number is 224 so I believe the company made this in the first year of guitar production witch was 1934. This information I found on the net. I do have photo’s of the guitar. It’s all rosewood and has a second sound chamber inside that is round and can be veiwed through the f-holes. the guitar also came with original string packages from the 30’s. I also have the case.

      • #102558
        Anonymous
        Guest

        Kevin, I also have a paramount guitar from the 30’s. I believe my guitar is from the first year of the Paramount banjo Co. Change over to guitars. The serial number is 224 so I believe the company made this in the first year of guitar production witch was 1934. This information I found on the net. I do have photo’s of the guitar. It’s all rosewood and has a second sound chamber inside that is round and can be veiwed through the f-holes. the guitar also came with original string packages from the 30’s.

      • #93193
        Anonymous
        Guest

        I have one also; had it since I was 12 years old (now almost 60. It sounds as good today as it did then. I’m not sure how to date it; I search the web from time to time trying to answer that question.

        • #110788
          Anonymous
          Guest

          : I was given a paramount archtop which i had to restore and would like to find out anything else about the maker of my guitar. As in where they where made, what years they where produced and really just anything Thanks Miles Canada

      • #85091
        Anonymous
        Guest

        Those guitars are plentiful and though not worth much, if you like it keep it around and enjoy it. : just had GIVEN to me a really nice guitar which has a unique neck whose neck angle can be adjusted on the fly. : had a really nice pro set up on it and it plays like a dream. : I have .jpg photos if anyone wants to see it, but my question is : how can I date it ? The serial no is model B 407. : Any of you guys over in the States help me on this? : Also with the guitar were some photos of the guy who owned it and one picture is taken in 1937. : Cheers : Kevin : UK

    • #45290
      Anonymous
      Guest

      Me guitar stinks. I’l lsell ya it for tree fetty or fiddy cent.

      • #85024
        Anonymous
        Guest

        : Me fiddy cent is worth more than your futtin dallar ill crack you over the head with a sac of crackies teeth.

        • #107255
          Anonymous
          Guest

          Now boys, quit your arguin’ or i’ll kick all yer arses.

    • #45288
      Anonymous
      Guest

      Can somone tells what is a good brand of pedal to get and what kind should I get

      • #85347
        Anonymous
        Guest

        I have the DOD grunge distortion pedal, and that thing rocks. My friend has a boss overdrive pedal adn the grunge pedal can replicate that boss pedals sound to the tee at about the 2nd out of 7 levels of distortion (meaning you can make this sound pretty damn distorted) I dont care what others say bad about this pedal cause chances are if their bad mouthing it that means they havent really tried it cause this things beast!

      • #107366
        Anonymous
        Guest

        : Can somone tells what is a good brand of pedal to get and what kind should I get BOSS,BOSS,BOSS. Always BOSS.

      • #85083
        Anonymous
        Guest

        Look,dude.For $50.00 get a Smash-Box.It is beautifuly E.Q.’d all notes in big chords rig out.Even on the G and D strings. It has one flaw,it’s a little frail.So,keep it CLEAN and try not to knock it around too much.Put it away when not in use. DS-1’s are o.k. but they’re not as open sounding as the SM-7. Pods are cool,but they’re too difficult to use live.And if you break it,you’re in a world of shit! At it’s price the SM-7 is disposable. So far the only(less $100)pedal that out does it,is the Rampage by Rocktron.Which is more flexible. Good Luck P.S.Make sure you invest in a decent amp though.

      • #85028
        Anonymous
        Guest

        Get a POD : Can somone tells what is a good brand of pedal to get and what kind should I get

      • #85053
        Anonymous
        Guest

        first of all,, i would think that your amp has distortion, but if it don’t,, then the best kind would be a digitech metal master

      • #85035
        Anonymous
        Guest

        Marlin is good

    • #45289
      Anonymous
      Guest

      I like sami hommm tac spetetti and meat ball and hotdog with relish oh yeah lot a relish o and chip and alll go in ma belly mmmmmmmmmmmmuckle

      • #84919
        Anonymous
        Guest

        I jsut pooed myself

    • #45287
      Anonymous
      Guest

      I have a Kay guitar I bought in 1953, I still play it from time to time, anybody can give me an idea of the value ?

      • #109266
        Anonymous
        Guest

        : I have a Kay guitar I bought in 1953, I still play it from time to time, anybody can give me an idea of the value ? I have a Kay guitar with stamp #N4 please tell me something about it…It’s missing the bridge….I bought it from a yard sale.

      • #84851
        Anonymous
        Guest

        $5, 000 US

    • #45286
      Anonymous
      Guest

      cool guitars at http://www.goatse.cx

      • #85073
        Anonymous
        Guest

        keep yer homo stuff on yer homo boards please : cool guitars at http://www.goatse.cx

    • #45285
      Anonymous
      Guest

      Ass

    • #45284
      Anonymous
      Guest

      Hi guys. I am a big fat idiot.

      • #107358
        Anonymous
        Guest

        Stop listening to rap and you could lose up to 50 pounds..

        • #115035
          Anonymous
          Guest

          rap rules so does eminem the best rapper ever

      • #84923
        Anonymous
        Guest

        . what ya doing all the time?? in the woods? in the woods?

        • #107198
          Anonymous
          Guest

          I’ll give you 20 pounds of pepsi if you kill Perry.

          • #111847
            Anonymous
            Guest

            Shup

      • #84899
        Anonymous
        Guest

        I rape small children.

        • #85081
          Anonymous
          Guest

          IP fowarded : I rape small children.

    • #45282
      Anonymous
      Guest

      http://www.Stitchmouth.50g.com (spread the word)

    • #45281
      Anonymous
      Guest

      If you don’t know StitchMouth, you will. We fight for Rock and Roll (pop punk must die) http://www.StitchMouth.50g.com

    • #45280
      Anonymous
      Guest

      If you don’t know StitchMouth, you will. We fight for Rock and Roll (pop punk must die) http://www.StitchMouth.50g.com

    • #45283
      Anonymous
      Guest

      does anybody knows any kind of patch… with a little of Mike Eizinger’s syle???? or another "that kind" guitar player??????? pleaseeeeeeee pleaseeeeeeeeeeeee pleaseeeeeeeeeeeeeeeeeeeeee

    • #45279
      Anonymous
      Guest

      i need giutar cords for weezers first album

      • #93267
        Anonymous
        Guest

        : i need giutar cords for chris de burghs first album

      • #86186
        Anonymous
        Guest

        : i need giutar cords for weezers first album hello there try http://www.guitar tab universe you`ll find all you desire there mate… have fun….

    • #45278
      Anonymous
      Guest

      Does anyone out there no if this company exist today or what years they were in business. Thanks

      • #109188
        Anonymous
        Guest

        : Does anyone out there no if this company exist today : or what years they were in business. : Thanks I bought a Voston six string in 1966. Excellent construction and quality. Still have it but it has a broken brace and the action needs to be adjusted, but other than that it’s been an excellent guitar.

      • #87885
        Anonymous
        Guest

        i have a 12-string bought in 1969. quality wood and finish. quality inlays, etc. but shitty construction and sound. the bridge is giving way, and is in need of reinforcing. how do i do that? thanks for the posting. good luck, jim in mississippi usa

    • #45277
      Anonymous
      Guest

      Download free videoclips by: Coleman Hawkins Julian Adderley "Cannonball" John Coltrane Charlie Parker Dizzy Gillespie Boney James 1986 VII Festival Jazz Jacksonville (Gerry Mulligan, Branford Marsalis, Nick Brignola) Jay Beckenstein (Spyro Gyra) Sophie Alour and other great artists… section: Videoclips Jazz/Sax => http://spazioinwind.libero.it/gabrielesax/ Thanks Gabriele (Italy)

      • #82585
        Anonymous
        Guest

        : Download free videoclips by: : Coleman Hawkins : Julian Adderley "Cannonball" : John Coltrane : Charlie Parker : Dizzy Gillespie : Boney James : 1986 VII Festival Jazz Jacksonville (Gerry Mulligan, Branford Marsalis, Nick : Brignola) : Jay Beckenstein (Spyro Gyra) : Sophie Alour : and other great artists… : section: : Videoclips Jazz/Sax => : http://spazioinwind.libero.it/gabrielesax/ : : Thanks :rocco (Italy)

    • #45275
      Anonymous
      Guest

      Is there a site where I can look up manufacturer logos in order to identify the maker of my guitar. It’s an older model with a logo I can’t identify. Thanks,Joe

      • #109275
        Anonymous
        Guest

        : Is there a site where I can look up manufacturer logos in order to identify the maker of my guitar? Thanks, Anna

    • #45276
      Anonymous
      Guest

      Experienced guitar-new to reggae…what would best guitar and amp be and how to get best tone?

      • #97743
        Anonymous
        Guest

        : Experienced guitar-new to reggae…what would best guitar and amp be and how to get best tone? the best guitar would be a Gibson Les Paul with a Fender twin reverb amp, just like Bob

      • #108121
        Anonymous
        Guest

        : Experienced guitar-new to reggae…what would best guitar and amp be and how to get best tone? clean tone on preferably a fender or fender sounding amp. maybe a little reverb and or tremolo pedal

    • #45273
      Anonymous
      Guest

      I am building a strat style guitar with preamp; does anybody have ideas on best location to route cavity for the battery box? I’ve heard of them placed on underside of the pickguard, but pulling it up everytime to change a battery is not all that appealing.

    • #45274
      Anonymous
      Guest

      I have software for pc{procesor must be>700mhz for best results}.Have more of 50 blend-pop,rock,heavy,hard,blues,jazz….great sound!Send me a mail for more!

    • #45272
      Anonymous
      Guest
    • #45271
      Anonymous
      Guest

      Hi, I can’t set a patch that I like with zoom 606. Can you tell me where can I find some patch to play Weezer, Blink 182, Nirvana and so on? Thanx : )

      • #91167
        Anonymous
        Guest

        I can’t work out how to preset an order of patches eg, A1 to F1 instantly, the manual isn’t much help.

      • #110443
        Anonymous
        Guest

        : Hi, I can’t set a patch that I like with zoom 606. : Can you tell me where can I find some patch to play van halen

      • #114430
        Anonymous
        Guest

        : Hi, I can’t set a patch that I like with zoom 606. : Can you tell me where can I find some patch to play linkin park, Blink 182, Nirvana and so on? : Thanx : )

    • #45268
      Anonymous
      Guest

      The World’s Most Romantic, Unique and Fun Dating Ideas… http://www.creativedateideas.com/?hop=surfside.300dates

    • #45270
      Anonymous
      Guest

      les paul copy by renegade

      This popular thread has been given its own page : les paul copy by renegade

    • #45269
      Anonymous
      Guest

      http://www.PedalSteel.us Magazine – For ALL types of Steel, Slide, and Pedal Steel Guitar Players! http://www.PedalSteel.us Magazine

    • #45265
      Anonymous
      Guest

      I want to have a dowland about the instrumental music

    • #45267
      Anonymous
      Guest

      Help me!! How I can to lock my Flod Rose for only drop the whammy bar? I want to use tremelo for strings go to flat. With a wooden Block, where I would to put this? Thanks.

    • #45266
      Anonymous
      Guest

      GP4 claims to have a WAV exporting feature, but everytime i try to export a song to WAV format, the audio file comes completely empty. I tried changing each and every of my midi setups, but none of them seemed to work ok to be rendered to WAV. And i can’t use wingroove, ‘cuz my soundboard’s midi quality is way better. The ideal for me is to export instrument by instrument to WAV with GP4, and yet, i can’t do it. What should i do?

    • #45263
      Anonymous
      Guest

      Husband had a guitar that said Frampton at the top – – black with gold – – possibly a copy of a Les Paul guitar – -he had it in the early 80s… Any one know who made this guitar? Sue

      • #82577
        Anonymous
        Guest

        Hi, Can you send me a photo? Maybe I can identify it for you. Are you interested in selling it? Grady : Husband had a guitar that said Frampton at the top – – black with gold – – possibly a copy of a Les Paul guitar – -he had it in the early 80s… Any one know who made this guitar? : Sue

      • #107372
        Anonymous
        Guest

        : Husband had a guitar that said Frampton at the top – – black with gold – – possibly a copy of a Les Paul guitar – -he had it in the early 80s… Any one know who made this guitar? : Sue No I don’t know who made it Sue, but just go ahead and mail it to me. LOL Just kiddin’ Peace 😉

    • #45264
      Anonymous
      Guest

      I would like some info on a Charvel i own it has serial:281185 neck plate says forth worth texas,it has 2 single coil picks and 1 humbucker a floy rose tremolo,is in white pearl colour,1 volum knob and 2 tone+3 3 small tone knobs . what modell is it ,is it a japanese mede guitar and from what year is it.

    • #45261
      Anonymous
      Guest

      looking for these guitars!

    • #45260
      Anonymous
      Guest

      Hi, everybody… This seems to be a very well-visited forum… Am I right???

      • #84864
        Anonymous
        Guest

        There’s only like 10 people here that give good advice, the others just talk shit and **** around, plus bob was dead on, its a waste posting anything here cuz no one ever answers your post…. And the pop ups are like every min, since they like advertising so much, i’ll do a little of my own…. Go to Ultimate-guitar.com, its way better and the forums will help you more.

        • #86319
          Anonymous
          Guest

          : There’s only like 10 people here that give good advice, the others just talk shit and **** around, plus bob was dead on, its a waste posting anything here cuz no one ever answers your post…. No – no one ever answers posts just the way you didn’t 🙂

      • #84843
        Anonymous
        Guest

        This site sucks and is nothing more than a popup advertising gimmick, there is no content here at all, looks like 90% of posts go unanswered, and almost all the answers are vulgur crap anyways. GoTo to wholenote.com, you’ll find it much better than this hole.

    • #45262
      Anonymous
      Guest

      Harmony H166 Parts

      This popular thread has been given its own page : Harmony H166 Parts

    • #45259
      Anonymous
      Guest

      12-String, Espana, made in finland

      This popular thread has been given its own page : 12-String, Espana, made in finland

    • #45258
      Anonymous
      Guest

      I have a Kramer electric guitar and i bought it from a guy in a band so i dont know much about it. Its mid to late 80’s and it has a custom paint job that looks kinda like an octopus. Im lookkin to sell it. I heard it was worth alot so if anyone could help me out i would appreciate it. THanks ZACH

      • #86349
        Anonymous
        Guest

        : I have a Kramer electric guitar and i bought it from a guy in a band so i dont know much about it. Its mid to late 80’s and it has a custom paint job that looks kinda like an octopus. Im lookkin to sell it. I heard it was worth alot so if anyone could help me out i would appreciate it. THanks ZACH any kramer before 1984 was most likely top of the line if the paint job is original. these were actually the better constructed kramers before they sold out and started making them in taiwan or korea

      • #86313
        Anonymous
        Guest

        : I have a Kramer electric guitar and i bought it from a guy in a band so i dont know much about it. Its mid to late 80’s and it has a custom paint job that looks kinda like an octopus. Im lookkin to sell it. I heard it was worth alot so if anyone could help me out i would appreciate it. THanks ZACH any kramer before 1984 was most likely top of the line if the paint job is original. these were actually the better constructed kramers before they sold out and started making them in taiwan or korea

    • #45257
      Anonymous
      Guest

      custom made guitars

      This popular thread has been given its own page : custom made guitars

    • #45254
      Anonymous
      Guest

      Hello All, I am looking for a kind of "multichannel" guitar pickup which is able to take each single string on an own output. Do you have such a product or could you give me any hints. thanks in previous Ralph

    • #45256
      Anonymous
      Guest

      Seville Guitar

      This popular thread has been given its own page : Seville Guitar

    • #45255
      Anonymous
      Guest

      I want to get an electrical guitar, but i dont know which kind to get. Id like a Wolfgang or a Fender Stratocaster, but will someone please tell me the best kinds out there?

      • #84905
        Anonymous
        Guest

        hmmmm…there is no such thing as the best guitar, there are lots of things that make a guitar better for the person who plays it.it depends on what kind of music you like and what sound your going for,what your style is.if your just starting your probly going to get a beginners guitar(which might not be the greatest guitar)but they work.you can get a good ibanez for about 300 or a squier for less than 100 but you will just have to go to you nearst music store(dont be embarresed)and pick up a few guitars plug em in and fuck around with them,see if you like the way certin guitars sound and how they feel on you…that is the only way you wiil find a guitars that is good for you.

    • #45253
      Anonymous
      Guest

      I recently purchased an Epiphone Sherarton II jazz style guitar and as it being my first electric guitar I was wondering if anyone had any pointers on the best way to restring it. It looks like you can either slide the strings directly out of the back of the bridge plate or take the bridge plate off. I don’t want to have to remove parts if it is not necessary. Any help would be greatly appreciated. Todd

    • #45252
      Anonymous
      Guest

      i want one but i dont want to pay 110 for a big piece of plastic so i need the dimentions so i can build one in wood shop….if you have one plz give me the dimentions of all the sides and thickness and all that good shit,and anything else you think would help thanx.

      • #100864
        Anonymous
        Guest

        yeah im buildin one for my warlock and the dimentions to that is 3 ft 10 in. long,1 ft at the bottem and the two little ones at the bottem are also a ft each and at the part where it spreads out its 1 ft and 16 in. wide and as for hight it duznt really fuckin matter as long as the shit fits,and yeah im buildin one for my warlock so i dunno if yours will fit but i hope i helped

    • #45251
      Anonymous
      Guest

      hey i want to have a guitar leason so help

      • #88053
        Anonymous
        Guest

        : hey : i want to have a guitar leason so help me find the greates leason

      • #93510
        Anonymous
        Guest

        : hey : i want to have a bassleason so help

      • #112379
        Anonymous
        Guest

        : hey : i want to have a guitar <B style="color:black;background-color:#A0FFFF">leason</B> so help

        • #112577
          Anonymous
          Guest

          : : hey : : i want to have a guitar leason help please

      • #86457
        Anonymous
        Guest

        What part of the world are you in?

      • #86325
        Anonymous
        Guest

        Hey Angel, go to http://www.guitartricks.com and click on my name, i have great lessons there for free, and if you get interested i do instuctional videos. Check it out

    • #45249
      Anonymous
      Guest

      I Have a Gibson Epiphone SG Juniour model in pure black with all original parts. It is in average condition to say I don’t know how old it is. I recentley bought it for £30 and wanted to know how much it is really worth. Pls help. Scott

      • #84870
        Anonymous
        Guest

        there worth about 400 new so it depends on the condition but probly from 250-300 if its in good shape

    • #45250
      Anonymous
      Guest

      Sigma Martin DR35

      This popular thread has been given its own page : Sigma Martin DR35

    • #45248
      Anonymous
      Guest

      DOD death metal distortion pedal with low and mid set a little over half and high wherever you want. play a guitar with humbukers preferably Duncan Design of any metal guitar (I play a Jackson) and set pick up switch to the front you can also through in a Q series cry baby but you lose sustain This is the best way I know and nobody can tell the difference

      • #82453
        Anonymous
        Guest

        : DOD death metal distortion pedal with low and mid set a little over half and high wherever you want. play a guitar with humbukers preferably Duncan Design of any metal guitar (I play a Jackson) and set pick up switch to the front you can also through in a Q series cry baby but you lose sustain : This is the best way I know and nobody can tell the difference

        • #113026
          Anonymous
          Guest

          the best cheap way to get the sound like me, is to buy a ( around 69$ ) blues-pedal, and an overdrive/distortion pedal.. kick the distortion or overdrive to the max, and play alittle wth the blues pedal while listening to som old G n’ R music.. ul find the perfect sound.. Sincerly yours, Slash alias. Saul Hodson

    • #45246
      Anonymous
      Guest

      flambeau guitar

      This popular thread has been given its own page : flambeau guitar

    • #45247
      Anonymous
      Guest

      I cant afford to keep buying the fluids, does anyone know other ways of cleaning bass strings.

      • #92386
        Anonymous
        Guest

        I find that dropping the bass strings in boiling water for a few minutes makes them clean and bright again so they sound like new. I actually heard that Sting did this so I tried it, works great.

    • #45244
      Anonymous
      Guest

      REST IN PEACE….the greatest guitar player that EVER LIVED. TOMMY BOLIN – James Gang, Deep Purple, Billy Cobham. Dont take my word for it…check out his music.

      • #84886
        Anonymous
        Guest

        R.I.P Damn,how did he die?? He was a BADD MOFO!!

        • #87129
          Anonymous
          Guest

          Tommy Bolin was from Avondale Colorado and his best work was with Zypher, fronted by a very dynamic female vocalist named Candie Givens, who also ODed. A great guitarist/songwriter, arguably the best.

        • #107370
          Anonymous
          Guest

          Bolin died December 4, 1976 of multiple drug overdose. He was 25 years old. Very sad.

          • #107663
            Anonymous
            Guest

            Jeez! I thought he died recently! Well,anyone reading this…..DRUGS MAKE YOU STUPID!!

            • #113040
              Anonymous
              Guest

              Tommy Bolin was a gifted individual who like the many others we’ve lost before, Hendrix, Morrision, Joplin, et. al. were so far ahead of their time, and were so sorely misunderstood that they sought solace in escape, the same way the man who cheats on his wife seeks solace in alcohol, etc…we’re only human, and if you had to deal with the pressures they had, you might have done the same thing. So why don’t we stop and think before we judge another persons character.

            • #113067
              Anonymous
              Guest

              Tommy Bolin was a gifted individual who like the many others we’ve lost before, Hendrix, Morrision, Joplin, et. al. are so far ahead of their time, and are so sorely misunderstood they seek solace in escape, the same way the man who cheats on his wife seeks solace in alcohol, etc…we’re only human, and if you had to deal with the pressures they had, you might do the same thing. So why don’t we stop and think before we judge another persons character.

    • #45245
      Anonymous
      Guest

      rest in peace….the greatest "all around" guitar player in the world….hands down!

    • #45243
      Anonymous
      Guest

      Where should I send my guitar-instrumental demo for a rewiev?

    • #45240
      Anonymous
      Guest

      Supro Guitar

      This popular thread has been given its own page : Supro Guitar

    • #45242
      Anonymous
      Guest

      Gibson SG-X Coral Color

      This popular thread has been given its own page : Gibson SG-X Coral Color

    • #45241
      Anonymous
      Guest

      Hi, I need a knob for the GFX 8. The foot switch needs slight repair, who would be the best man for the job, ie a guitar shop/ I don’t think Zoom hand out parts or do repairs you see 🙁

      • #82933
        Anonymous
        Guest

        : Hi, I need a knob for the GFX 8. The foot switch needs slight repair, who would be the best man for the job, ie a guitar shop/ I don’t think Zoom hand out parts or do repairs you see 🙁 call samsontech custumer service at 1-800-372-6766 they have all the parts you need for your Zoom Gfx 8….

        • #111941
          Anonymous
          Guest

          : : Hi, I need a knob for the GFX 8. The foot switch needs slight repair, who would be the best man for the job, ie a guitar shop/ I don’t think Zoom hand out parts or do repairs you see 🙁 : call samsontech custumer service at 1-800-372-6766 they have all the parts you need for your Zoom Gfx 8…. oops….If you cannot handle the repair of the pedal you can go to http://www.knpelectronics.com and they repair parts at $35 an hour… good luck

    • #45238
      Anonymous
      Guest

      In the spirit of international understanding and cooperation among guitarists I am seeking to compile a translation list for all languages for parts of the guitar. There is very little in the official translation books or elsewhere for these terms. Not even in those big Web translation programs. It may not be important to the rest of the world, but it is to us. Please submit your translations here and I will publish it for all the world to see and use. Please submit the easy FORM below or email your answers to me at [email protected].    Thank you for your help,  Beth Vance

    • #45239
      Anonymous
      Guest

      i need the color codes for prs pups

    • #45236
      Anonymous
      Guest

      Charvel STX Deluxe guitar

      This popular thread has been given its own page : Charvel STX Deluxe guitar

    • #45237
      Anonymous
      Guest

      Hayashi guitar

      This popular thread has been given its own page : Hayashi guitar

    • #45233
      Anonymous
      Guest

      dear ser/lady i need a program that be abel to turn my computerto the good guitar electric fxbox. i will be thank you if you guid me to my pleases. pleas dont forget to anser this email. tank you

      • #84845
        Anonymous
        Guest

        : dear ser/lady : i need a program that be abel to turn my computerto the : good guitar electric fxbox. : i will be thank you if you guid me to my pleases. : pleas dont forget to anser this email. : tank you FUCKING ILLITERATE!

    • #45234
      Anonymous
      Guest

      i was wondering could anyone tell me, how could i get a good metal,alternative punk sound off my distortion pedal?(for my guitar)

      • #107369
        Anonymous
        Guest

        : i was wondering could anyone tell me, how could i get a good metal,alternative punk sound off my distortion pedal?(for my guitar) Treble up 100% mids OFF Bass about 90% Drive/distortion 80-90%

    • #45235
      Anonymous
      Guest

      i have had my fender strat since the 12th december 1964 bought at Hessy’s liverpool it’s a bit worse for ware and would like to buy original parts for it.where can i find a place to buy parts and get it re-sprayed

    • #45231
      Anonymous
      Guest

      Does anybody know what a 40th anniversary strat is worth. or have any feedback on them?

      • #86348
        Anonymous
        Guest

        : Does anybody know what a 40th anniversary strat is worth. or have any feedback on them? ===========================> worth about 75 to 125 dollars more than when purchased depending on the finish and hardware color. Does it have the 40th emblem on the headstock?

    • #45230
      Anonymous
      Guest

      To readers in New Zealand: Where would I find a digitech XP300 ‘Space-Station.’Or a Hughes and Kettner Tube factor Distortion.

    • #45232
      Anonymous
      Guest

      hello, I have an old guitar who looks like a Fender Strat but is not a Fender Strat. The brand is Vega Power. I would like to change the pickups for an better sound. I consider the Fender Vintage Noiseless or Lace sensor gold. ALso the Seymour duncan Quarter Pounds. Does anybody have some suggestions to get a very good sound. Thank in advance for your help. Paul

      • #85459
        Anonymous
        Guest

        : i have a pussy but im a young man what should i do, <3 man with the pussy

      • #95687
        Anonymous
        Guest

        Paul, First off the guitar you have is not a bad guitar, however; it be better to try finding an inexpensive strat. NOT A Squire but a good Strat. But if you like the you guitar try looking into EMG’s. They make a humbucker that will fit into a single coil hole. Emg pickups are great. you can get the warmth of a strat or les paul AND the edge of a Schecter or Ibanez. They cost about $60-$90./EA.

    • #45229
      Anonymous
      Guest

      does anyone know a good site for downloading acords for all artists

      • #87147
        Anonymous
        Guest

        : does anyone know a good site for downloading acords, ex du gammla fria nord av lars winerbeck

      • #101405
        Anonymous
        Guest

        Does anuone knows a site where I could find a Guitar acords and notes for solo playing?

      • #95115
        Anonymous
        Guest

        : does anyone know a good site for downloading acords for all artists

        • #96314
          Anonymous
          Guest

          : : does anyone know a good site for downloading acords for beatles, or anyone?

    • #45227
      Anonymous
      Guest

      I am thinking of electric pick up amp Taylor 810 any ideas..Problems ect…

      • #107081
        Anonymous
        Guest

        : I am thinking of electric pick up amp Taylor 810 any ideas..Problems ect… I use the Dean Markley "Sweet Spot" UST, through a Baggs "Para-Coustic" pre-amp/DI for all of my performing instruments…excellent P/U, in my opinion.

    • #45228
      Anonymous
      Guest

      Does anyone have a circuit diagram for the Carlsbro stingray guitar amp. my mates’ is just producing a hum and thats it – trying to fix it

    • #45225
      Anonymous
      Guest

      Does anyone know which guitar pedal rammstein uses in their tracks????? Kay B

      • #89989
        Anonymous
        Guest

        rammstein uses a flanger pedal

      • #95090
        Anonymous
        Guest

        hey, its jon again. i was wondering what kind of pedals Richard uses for all of the song. i need to get one. im dying.i would appreciate it if you could answer back as soon as possible. thanks for ur time, jonthan

    • #45226
      Anonymous
      Guest

      What would you put in the blank of this sentence: "Teenagers have thought the guitar was cool since __________." Who do teenagers think is the coolest guitar player now? Thanks a lot for your thoughts

    • #45223
      Anonymous
      Guest

      I was wondering what type of guitar straps are better?? the nylon kind or the leather kind?

      • #84867
        Anonymous
        Guest

        well both of the above guys are right. i would also add that the wider a strap you get the better it is a displacing the weight. so take that into consideration too.

      • #84860
        Anonymous
        Guest

        : I was wondering what type of guitar straps are better?? the nylon kind or the leather kind? i prefere the nylon kind , more comfy

      • #107083
        Anonymous
        Guest

        I’d say leather if you’re looking for comfort. Nylon straps are cheap n’ cheerful, and sometimes very pretty ! So, just go for what you like – Comfort, or looks 🙂

    • #45224
      Anonymous
      Guest

      Tom DeLonge is GAY!!!

      • #98074
        Anonymous
        Guest

        jonny is gay 07834239673 to giv him abuse

      • #92812
        Anonymous
        Guest

        he prob is cause i know a gay tom as well

      • #89503
        Anonymous
        Guest

        Tom Myers is a flaming homo… thats the real gay tom!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

      • #81358
        Anonymous
        Guest

        pls tel me he’s not really gay cos i luv him. but if he is ile kil ur eva lovin asre in2 nxt year : Tom DeLonge is GAY!!! i hope ur jus screwin roun cos if he is ay ile hun u down 4 breakin tht 2 me like tht!

      • #80330
        Anonymous
        Guest

        one time tom delonge even said that he was gay he even has a vidio of himself f$*king travis barker in the ass the only reason he married a girl was to prove people wrong

        • #104435
          Anonymous
          Guest

          learn how to spell you dumbshit

        • #80651
          Anonymous
          Guest

          REALLY? TOM GOAD IS GAY

      • #102947
        Anonymous
        Guest

        Tom Goad is GAY!

      • #113769
        Anonymous
        Guest

        TOM LIBBERACHI GAY!

      • #89177
        Anonymous
        Guest

        : Tom Cox is GAY!!!

      • #89171
        Anonymous
        Guest

        : Tom Cox from Australia Queensland 4160 is GAY!!!

      • #107090
        Anonymous
        Guest

        Just ’cause he runs around in his undies doesn’t mean he’s gay 🙂

    • #45222
      Anonymous
      Guest

      I have Just bought a BOSS GT6 effects processor to use with my Marshall DSL head to find that when i try to use the effects loop on the back of the amp to connect the GT6 up it doesn’t allow me to use all the patches. This does not occur if I use the input at the front of the amp. I have talked to a guy at Roland who tells me the two units are inconpatible, but not one of the sales people in all the shops I have called are aware of theis problem. Has anyone else had a similar problem and what did you do!

    • #45221
      Anonymous
      Guest

      I bought a used am. stratocaster with serial number begin with Z1 ( 2001 ? ). Excellent condition, only one string guide, white pearl shell pickguard, no TBX or deltatone, only seven pin of selector wired, no inscription on back of pickups. Nice tone, but what about these pickups ? I think Texas Special but how can I be sure ? Can it be an AM standard ( but no writing on pickups ! ). Thanks a lot.

      • #92224
        Anonymous
        Guest

        Hi, guess you are right. I also owning a strat beginning with z1 with the same features you have talked about. It is a New American Standard Stratocaster Texas Special manufactured in 2001. Best, Michael : I bought a used am. stratocaster with serial number begin with Z1 ( 2001 ? ). Excellent condition, only one string guide, white pearl shell pickguard, no TBX or deltatone, only seven pin of selector wired, no inscription on back of pickups. Nice tone, but what about these pickups ? I think Texas Special but how can I be sure ? Can it be an AM standard ( but no writing on pickups ! ). : Thanks a lot.

    • #45220
      Anonymous
      Guest

      Boss ME-6 User manual

      This popular thread has been given its own page : Boss ME-6 User manual

    • #45219
      Anonymous
      Guest

      MY SON LIVING IN ESTORIL TAKES CLASSIC GUITAR LESSONS.I AM LOOKING FOR A MATSUOKA 80 CLASSIC GUITAR. HOPEFULLY THERE ARE STOCKISTS OR DEALERS IN PORTUGAL. PLEASE HELP.

      • #96164
        Anonymous
        Guest

        hi, im exporting A b grade rose wood.with straight grains.with out any crack clear wood.front back and finger board.very competitive rates.please contact

      • #83715
        Anonymous
        Guest

        I have one good condition Matsuoka 80 Classical GUitar selling now in ebay. Please follow the link to look for it, http://www.ebay.com. Item No. 2372240186. : MY SON LIVING IN ESTORIL TAKES CLASSIC GUITAR LESSONS.I AM LOOKING FOR A MATSUOKA 80 CLASSIC GUITAR. : HOPEFULLY THERE ARE STOCKISTS OR DEALERS IN PORTUGAL. : PLEASE HELP.

    • #45218
      Anonymous
      Guest

      I have an old Gibson acoustic guitar (ES-5825) is the number on the back of the neck. I think it might be a Roy Smeck series. Any information on this guitar would be great.

    • #45217
      Anonymous
      Guest

      J40 gibson

      This popular thread has been given its own page : J40 gibson

    • #45216
      Anonymous
      Guest

      HOW TO RESTRING A FENDER STRAT???

      This popular thread has been given its own page : HOW TO RESTRING A FENDER STRAT???

    • #45215
      Anonymous
      Guest

      I bought a second hand Fender Telecaster and the logo looks real on the headstock, but I can’t find a serial number on it anywhere. It says ‘Made in Japan’, that’s all. Is this is a copy passed off as the real thing? Is there another way to tell apart from the serial number? Any help greatly appreciated.

      • #85919
        Anonymous
        Guest

        HI. IT SOUNDS LIKE YOUR TELECASTER IS A FENDER TELECASTER BUT AS ITS MADE IN JAPAN MEANS ITS A COPY .BEST WAY TO CHECK IF YOU HAVE A REAL FENDER OF ANY KIND IS LOOK AT YOUR BRIDGE AND ON YOUR BRIDGE SETTINGS IT SHOULD BE STAMPED FENDER ON ALL OF THEM .THE OTHER WAY TO SEE IF ITS REAL LOOK AT THE BACK OF THE HEADSTOCK AND ON EACH MACHINEHEAD FENDER SHOULD BE STAMPED ON EACH of the MACHINEHEADS ERNIE

    • #45214
      Anonymous
      Guest

      nOW A DAYS THERE ARE no guiatr heroes just a bunch of kids playing simple power chords, nobody’s cultivating the same musicianship that Yngwie had, the grace of Steve Vai, Joe Satriani’s sonic sound and the Shred attack of Petrucii,Vinnie Moore, Paul Gilbert,Van Halen Iron Maiden, The awsome leads of Marty Friedman, Tracii guns, Blues Sraceno,Vito Bratta, Bettencourt, And many great talents, it seems that only Zakk Wylde is the one standing, glory to him, and no one in the mainstream these days can match his guitar playing,. All of true guitar fans outhere wake up and be a real, LEAD guitarist,it’s not just that you’re loud it’s the melodic and fast furious solos and a hard drineg riff…Power to metal guitars that will always reign.

      • #107087
        Anonymous
        Guest

        You must have forgot kurt hammet, eric clapton, b.b king, joe satriani is still around playing, mark tremonti.

        • #112095
          Anonymous
          Guest

          the guy from metallica sucks ass he is the worst guitarist i have ever heard play. I think Jimmy Page should be in the number 1 spot for guitar god of all time. the guy from metallica (who i cant remember the name of) shouldn,t be a guitar god at all.

    • #45213
      Anonymous
      Guest
    • #45211
      Anonymous
      Guest

      whats this worth? gibson can’t help. got pics HELP!

    • #45212
      Anonymous
      Guest

      i haven’t seen smeagol on the board in awhile. you still alive out there dude?? 🙂 ,, any way i need help deciding which strings to get. i have an ibanez icx and,, well whut ones would you recommend?

      • #84559
        Anonymous
        Guest

        I usually just go for D’Addario or GHS. I tend to change strings frequently and can’t afford all the high end stuff on a regular basis. As far as the guage of the strings I can’t really say without more information on your playing style, type of music you like, scale length of the guitar, etc.

        • #107076
          Anonymous
          Guest

          D’addario 9’s are a pretty nice gauge and brand. 🙂

    • #45210
      Anonymous
      Guest

      I CANT FIGURE OUT HOW TO DO THIS WINMX! IT WONT LET ME IN! IT ONLY SAYS CONNECTING WITH A BLINKING YELLOW LIGHT.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX?

      • #95458
        Anonymous
        Guest

        i know how to use winmx, but mine wont connect sometimes .. and when it doesnt connect i can download songs..so what do i do?

        • #97413
          Anonymous
          Guest

          I just got winmx and i don’t understand how to use itwill someone help me.

        • #97416
          Anonymous
          Guest

          I just got winmx and i don’t understand how to use itwill someone help me.

      • #82300
        Anonymous
        Guest

        Are we supposed to care that you are an idiot? Tough shit for you asshole…

        • #89412
          Anonymous
          Guest

          i may be able to help.i have had WINMX for about 2 months now.i have figured out some things.the songs that are in red or say for example–23 in queue means there are 23 people in line for that track you will be #24.just be patient and your turn will eventually come up.instead go for the songs that are in green or say for example-2 of 6 available. click on the song then click "download" on the choices above.if its being nice it should say "waiting for network reply" if it doesnt work try another song available.if it does work it will say "connecting".when a blue box comes up youve succeeded and it should start with 1% then 2%.this means how much of the song is downloading.to the very right of the screen you will see the timeL with green or flashing numbers underneath it {meaning how much time is remaining}.sometimes 33:00 or 25:00 for example means how long it will take to load.if it says like 2 hours or so forget it go for another one.i’m understanding with my dial-up’s slow-ass connection i have i have to be patient.its frustrating i know but give it a chance i have hundreds of songs just in a short time and you will to.if you have a burner and want to burn these songs to disc and may not know how,e-mail me back.hope this was helpful.have a good one.if its still blinking yellow sometimes it can take up to 5 minutes or so.check also on someone elses name if others share your computer,click on their browser to see if it will work.

          • #99814
            Anonymous
            Guest

            Hi Max, I followed your reply to Tough..thanks it worked just great.

      • #110463
        Anonymous
        Guest

        : I CANT FIGURE OUT HOW TO DO THIS WINMX! i downloaded a song then i double clicked on it 2 play, and now i dunno where it has gone where do all my songs go wen iv downloaded them? help

        • #111420
          Anonymous
          Guest

          CHECK YOUR "MY DOCUMENTS" OR "MY MUSIC".ANY MORE HELP LET ME KNOW

          • #111893
            Anonymous
            Guest

            Maaaaaax!

      • #81334
        Anonymous
        Guest

        : I CANT FIGURE OUT HOW TO DO THIS WINMX! IT WONT LET ME IN! IT ONLY SAYS CONNECTING WITH A BLINKING YELLOW LIGHT.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX?

        • #82295
          Anonymous
          Guest

          : : I CANT FIGURE OUT HOW TO DO THIS WINMX! IT WONT LET ME IN! IT ONLY SAYS CONNECTING WITH A BLINKING YELLOW LIGHT.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX?

          • #89386
            Anonymous
            Guest

            DO YOU NEED SOME HELP USING WINMX.?

            • #99078
              Anonymous
              Guest

              : DO YOU NEED SOME HELP USING WINMX.? yah i have had it up for like 2 days and it still says connecting. Whats wrong with it? PLEASE HELP

      • #101972
        Anonymous
        Guest

        I cant get it to download!

      • #98371
        Anonymous
        Guest

        Hi, I started using winmx and kind of know how it works, but if i say start tonight and select a list of songs – they higlight in blue and are remotely queued I get that bit, I move up the list and sometimes get the song if I make it to the top of the queue. BUT if I log off and come back later then those same seections are stil on my list and I can click find sources now, but wil this mean its looking to see if that user who has the song is online then and there? And since the songs have "turned red" is it possible to get them queued again and into the blue again? I hope this makes sense cheers.

      • #96303
        Anonymous
        Guest

        you are actually paying for that shit? haha, you can download it free anywhere. seriously its not that hard

        • #96550
          Anonymous
          Guest

          sorry but winmx isn’t very hard 2 use… my 5 year old sister can use it

      • #85013
        Anonymous
        Guest

        : I CANT FIGURE OUT HOW TO DO THIS WINMX!I DONT KNOW HOW TO DOWNLOAD FILES.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX?

      • #82480
        Anonymous
        Guest

        Why is my downloading going so damn slow and why does it always say remotley queing. i better not be paying for this. i just startes 2 days ago. help

        • #98871
          Anonymous
          Guest

          : Why is my downloading going so damn slow and why does it always say remotley queing. i better not be paying for this. i just startes 2 days ago. help

          • #111400
            Anonymous
            Guest

            i may be able to help.i have had WINMX for about 2 months now.i have figured out some things.the songs that are in red or say for example–23 in queue means there are 23 people in line for that track ,you will be #24.just be patient and your turn will eventually come up.instead go for the songs that are in green or say for example-2 of 6 available. click on the song then click "download" on the choices above.if its being nice it should say "waiting for network reply" if it doesnt work try another song available.if it does work it will say "connecting".when a blue box comes up youve succeeded and it should start with 1% then 2%.this means how much of the song is downloading.to the very right of the screen you will see the "timeL" with green or flashing numbers underneath it {meaning how much time is remaining}.sometimes 33:00 or 25:00 for example means how long it will take to load.if it says say 2 hours or so forget it go for another one.i’m understanding with my dial-up’s slow-ass connection i have i have to be patient.its frustrating i know but give it a chance i have hundreds of songs just in a short time and you will to.if you have a burner and want to burn these songs to disc and may not know how,e-mail me back.hope this was helpful.have a good one

            • #112688
              Anonymous
              Guest

              when i try to download a song it will but after awhile it will not download anything it always says connection timed out every time why?

        • #93918
          Anonymous
          Guest

          Reply to all who are confused to this Brilliant software. WinMX is COMPLETELY FREE to use. When the software is started at first it asks you what connection speed you have 56K, 128K, Cable, DSL, ADSL etc. If you are unsure simply select UNKNOWN and then select a username to be displayed online. All this software does is shares your My Music folder or any other you have allocated for peer2peer. You goto the main page and click on the search and enter the name of the group, artist or song and it will search everyone who has the network with the search parameters you have entered. If there is then simply click on the selected song or artist and click Download ( or double click ) and it will start to download. Click on the Transferes button on the main page and this will diplay all your current downloads. Remember that you can only download the song if the person you have selected to download from is currently online at the same time otherwise you will be placed in a queueing system along with others. If you are in a queue then you could serach for similar songs and this might resolve it. Hope this helps

      • #114067
        Anonymous
        Guest

        I am a first time user to WinMX. Can someone please tell me how to use WinMX. I thought it would be simple but everytime I click download it starts to download and then eventually the download turns red and I don’t know what to do. Thanks

      • #86174
        Anonymous
        Guest

        : I CANT FIGURE OUT HOW TO DO THIS WINMX! IT WONT LET ME IN! IT ONLY SAYS CONNECTING WITH A BLINKING YELLOW LIGHT.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX? winmx is hard to get your head round… you need to go into the settings and change them around… downloads to the highest it will go, uploads bout half way and the rest on full….you need to be patience with this one i preffer Kazza myself it`s easier and you get more options…winmx is free…kazza is free….. try kazza light….

        • #116475
          Anonymous
          Guest

          : : I CANT FIGURE OUT HOW TO DO THIS WINMX! IT WONT LET ME IN! IT ONLY SAYS CONNECTING WITH A BLINKING YELLOW LIGHT.AM I PAYING FOR THIS SHIT? CAN SOMEONE TELL ME WHAT TO DO TO USE MY WINMX? : winmx is hard to get your head round… you need to go into the settings and change them around… downloads to the highest it will go, uploads bout half way and the rest on full….you need to be patience with this one i preffer Kazza myself it`s easier and you get more options…winmx is free…kazza is free….. try kazza light…. Dan…… Zasto kad upisem naziv izvodjaca i pjesme i kliknem search ili download nista se nedesava vec mi se neke dr.pjesme skidaju???

    • #45209
      Anonymous
      Guest

      Everyone check out this Robert Randolph guy! I just listened to his CD today adn it was AMAZING. He’s even got a contest going to win a steel guitar!

      • #87627
        Anonymous
        Guest

        : Everyone check out this Robert Randolph guy! I just listened to his CD today adn it was AMAZING. He’s even got a contest going to win a steel guitar!

        • #115212
          Anonymous
          Guest

          Not only have I heard him, I also know Robert Randolph

    • #45207
      Anonymous
      Guest

      Soy un guitarrista zurdo que quiere comprar una guitarra electrica,la marca que he encontrado con mas modelos zurdos es Stagg,quisiera saber que tal es esta marca.Si me recomindas otras marcas.Gracias!

    • #45206
      Anonymous
      Guest

      Could someone PLEASE help me Identify this model? I havent seen any like it on the website or anywhere. If I need parts I dont know what to get. Its a flatback acoustic with electric & 3 band eq. Heres the weird thing… Its like a bright sunburst color but with a flame shape sound hole instead of the usual round one. all it says is Morris on the headstock. It has 6 tuners on 1 side. I realy need someones help. Is this a rare guitar? Thanks again.

    • #45208
      Anonymous
      Guest

      ANY KIND!

    • #45205
      Anonymous
      Guest

      Can anyone help me with a manual for the boss me 6 guitar effects pedal. Thankyou

      • #109196
        Anonymous
        Guest

        Hey man try this PRODUCT SUPPORT – THE MIDI STORE … with the pedals of the ME-6. This allows a user to treat the ME-6 as 6 … at will with the footswitches, just as if you had individual BOSS compact pedals. … http://www.synthman.com/roland/support/ turbostarts/TURBO/ME6.html – 5k – Cached – Similar pages hope its a help rock on : Can anyone help me with a manual for the boss me 6 guitar effects : pedal. : Thankyou

        • #112722
          Anonymous
          Guest

          i have the manual if you want me to scan it and email it. : Hey man try this : PRODUCT SUPPORT – THE MIDI STORE : … with the pedals of the ME-6. This allows a user to treat the ME-6 as 6 … at will with : the footswitches, just as if you had individual BOSS compact pedals. … : http://www.synthman.com/roland/support/ turbostarts/TURBO/ME6.html – 5k – Cached – Similar pages : hope its a help : rock on : : : Can anyone help me with a manual for the boss me 6 guitar effects : : pedal. : : Thankyou

    • #45202
      Anonymous
      Guest

      I am looking at buying my 1st acoustic guitar. I would like to keep it under $250 and something that will be easy to play. So far it seems the Ibanez AW10 and the Washburn D10S appear to best. Any recommendations?

      • #98824
        Anonymous
        Guest

        I say Ibanez! Im getting it soon as well, with a stika spruce top ( solid!!! sounds much better then laminated ) diecast tuners ( stay in tune longer ) for such a bloody low price it cant be better for you, really, its not a cheap peace a junk for that price, its rather amazing

    • #45204
      Anonymous
      Guest

      i am trying to get a good Watery sound from my effects, i was wondering if anyone out there has any good sugesions. i have tride auto wah tremelo different delays and phasers and i just cant get the right combo.

      • #84599
        Anonymous
        Guest

        What kind of Phaser do you use?? The Boss PH-2,mixed with a nice chorus can be very liquid. PH-2’s are wild phasers that have lots of resonance to them. Good Luck

        • #107113
          Anonymous
          Guest

          right now i am using the Johnson Millenium so i have a very large selection of phasers. i will mess around a little more and see what i can come up with. Thanks

    • #45203
      Anonymous
      Guest

      vintage for price -consider ther cheapest models – miked up u will be stunned by thw sound – I used to rate my ovation etite spatial which cost me … go resonator. Try the wood body ones – Mr bicuit – discontiued ephiphone model is a perfect intro. the metal bodied ones are aspecialist instrument, look for the cheeper american models

    • #45201
      Anonymous
      Guest

      Charvel Spectrum

      This popular thread has been given its own page : Charvel Spectrum

    • #45199
      Anonymous
      Guest

      duz anybody know any thing about where i can get info about my axe. i can`t find shit.

    • #45200
      Anonymous
      Guest

      I like my old Takamine F-400 12-string: sounds OK, has been a good friend for 26 years. WATCH OUT for Guild 12-strings these days: warranty, string-buzzin’, and other problems, often, so proceed with caution. Keep jingle-janglin!

      • #107121
        Anonymous
        Guest

        : I like my old Takamine F-400 12-string: sounds OK, has been a good friend for 26 years. WATCH OUT for Guild 12-strings these days: warranty, string-buzzin’, and other problems, often, so proceed with caution. Keep jingle-janglin! Sorry to differ with you…Guilds (even the Fender ones) are vastly superior instruments over Taks…if you can only afford a Japanese instrument (and no one’s knocking folks with limited budgets), buy an Alvarez…much better instrument than a Tak @ 1/2 the price!

        • #115707
          Anonymous
          Guest

          : : I like my old Takamine F-400 12-string: sounds OK, has been a good friend for 26 years. WATCH OUT for Guild 12-strings these days: warranty, string-buzzin’, and other problems, often, so proceed with caution. Keep jingle-janglin! : Sorry to differ with you…Guilds (even the Fender ones) are vastly superior instruments over Taks…if you can only afford a Japanese instrument (and no one’s knocking folks with limited budgets), buy an Alvarez…much better instrument than a Tak @ 1/2 the price! *I know what you’re saying…I’m just saying that the new Guilds are of inconsistent quality, so be careful when shopping.

    • #45197
      Anonymous
      Guest

      Anyone ever hear of a Ramirez GB3 or GR3? This would supposedly be a model not exported from Spain. May be bogus. Thanks

    • #45198
      Anonymous
      Guest

      I’ve got a mesa triaxis and a 2:90 power amp. When I play powerchords on the low E string the sound is blurry. I can’t clear it up. what can I do. Is it the power amp or the triaxis?? I am looking for the Gary Moore kind of sount. Very distorted but still clear. I’m talking about the "still got the blues" sound

      • #107384
        Anonymous
        Guest

        Hello Harm… I can relate to that problem. I have the same setup as you have and I had to do some seriuos tweaking berfore I got it the way I wanted. The unfocused and flabby bottom end that you are describing may be the result of too much bass on the triaxis. Depending on what lead mode you are using (Ld1 /Ld2) the bass control acts different. I’m using Lead2 Yellow as primary and using the deep switch activated on the 2:90. Roll back on the bass a bit add an EQ between the Triaxis and the 2:90 if you are lacking bottom end. The reason for the flabby bottom may be because in lead 2 the gain is added after the signal has passed the tone controls. So adding more bass to the signal will not produce more bass from the speakers but will result in distrorting the bass even more. There are some custom modifications that can be made to the Triaxis the are relativly cheap. But I think you can get pretty good results from experimenting somewhat. I hope this will help you getting the sound you are after. If not let me know…

    • #45196
      Anonymous
      Guest

      I found this Morris MD-500 on the side of the street about 4 years ago and I can’t find anything about how much it was/is now. So any help would be awesome! -Tiffany AIM: tiffson13

      • #98691
        Anonymous
        Guest

        Hi Tiffany, I have a Morris MD-500 which I bought in maybe ’85 and I thing I spent around 150 on it. I hope this helps. Let me know what else you’ve found out.

    • #45195
      Anonymous
      Guest

      As you may guess I don’t know lot about guitars, but I have a guitar I bought in Brazil. Not real expensive but mid range. Now-a-days it is a problem. When I tune it in it is great in C when I’m playing with others, but change key and it sounds out of tune. It’s like it will only tune to one key. Even good players have the same problem with it.What’s wrong with it?

    • #45193
      Anonymous
      Guest

      I CANT SEEM TO GET A REALLY GOOD METAL SOUND FROM MY LINE6 SPIDER AMP. I USE THE AMPS DISTORTION. ANY ADVICE ON TONE SETTINGS?

      • #97938
        Anonymous
        Guest

        : I CANT SEEM TO GET A REALLY GOOD METAL SOUND FROM MY LINE6 SPIDER AMP. I USE THE AMPS DISTORTION. ANY ADVICE ON TONE SETTINGS? Is there a website where I can get tone setting for line 6 spider like crazy train and purple haze you the main setting?

      • #93604
        Anonymous
        Guest

        : I CANT SEEM TO GET A REALLY GOOD METAL SOUND FROM MY LINE6 SPIDER AMP. I USE THE AMPS DISTORTION. ANY ADVICE ON TONE SETTINGS? i got one go to insane preset then set your gain to half then your low to a little less than half then your mid to a little less than half then your high to full REMEMBER: you must keep your gain at medium or you will get a muddy sound

      • #94845
        Anonymous
        Guest

        : I CANT SEEM TO GET A REALLY GOOD METAL SOUND FROM MY LINE6 SPIDER AMP. I USE THE AMPS DISTORTION. ANY ADVICE ON TONE SETTINGS? ok dude…i am an expierienced metal player…ive been gigging since i was eleven in metal bands…wut u do is set the amp to recto(the insane sound is worthless…there is a point where u can have too much distortion) and set drive on all the way…bass at around 8, mids around 7, highs from 9 to ten, channel volume all the way, dial in a lil less than half up on chorus, no echo(every once in a while, some ping pong is cool), if u like reverb(i dont) put it up 3 to 4 notches and set the master where you like it…this is a wonderful sound…enjoy ~jojo

      • #86006
        Anonymous
        Guest

        buy a new amp!

    • #45194
      Anonymous
      Guest

      I have just begun playing the guitar. I know some of the chords and can play them pretty clean for the most part, but I have no direction. I think that lessons would help out a lot, but at the moment I do not have the time or the money. I was wandering if whoever is going to read this can tell me a few songs and strum patterns that I might be able to practice.

    • #45191
      Anonymous
      Guest

      http://mywebpages.comcast.net/fredsiegle/strat/index.html Rare Ibanez one of a kind prototype pre-law-suit (1976) Strat copy. Custom made at the Fuji-Gen Gakki factory in Japan. This guitar is an Ibanez, but it’s built like a Fender with solid wood and one piece construction throughout. It is a prototype that Ibanez was considering for production. Because of the high quality construction, they decided it would be too expensive to build for the copy market. I purchased this guitar in 1977 directly from the Ibanez distribution center in Bensalem, PA when I was the manager of the repair department there. I used it for gigs and recording for a couple of years and then played it only a few times each year after that. I have recently decided to offer it for sale.

      • #110598
        Anonymous
        Guest

        Saw something about it on Ebay. I was the janitor at Bensalem, PA and altered all the drawings that were copied from Fender. That’s why they will always be worthless Ibanez junk that only a clueless ebayer would buy. : http://mywebpages.comcast.net/fredsiegle/strat/index.html : Rare Ibanez one of a kind prototype pre-law-suit (1976) Strat copy. : Custom made at the Fuji-Gen Gakki factory in Japan. : This guitar is an Ibanez, but it’s built like a Fender with solid wood and one piece construction throughout. : It is a prototype that Ibanez was considering for production. Because of the high quality construction, they decided it would be too expensive to build for the copy market. : I purchased this guitar in 1977 directly from the Ibanez distribution center in Bensalem, PA when I was the manager of the repair department there. I used it for gigs and recording for a couple of years and then played it only a few times each year after that. I have recently decided to offer it for sale.

    • #45192
      Anonymous
      Guest

      coming to florida 17-29 April. Like to buy a used voodu valve and see a couple of bands. Any web sites that might help. Thanks Ray

    • #45189
      Anonymous
      Guest

      Ware can I buy a set of intonation keys for a Floyd Rose

    • #45190
      Anonymous
      Guest

      Anyone know where I can get the year of my fender twin amp CR 269293

    • #45188
      Anonymous
      Guest

      I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these?

      • #100094
        Anonymous
        Guest

        hi, i am 16 years old and making an electric guitar. i have no idea what the measurements are though! if anyone has some idea of any electric measurements please email me, thnx

      • #85034
        Anonymous
        Guest

        Can someone email me the plans and how to make an electric guitar for any model

        • #85180
          Anonymous
          Guest

          : Can someone email me the plans and how to make an electric guitar for any model

          • #98651
            Anonymous
            Guest

            : : Can someone email me the plans and how to make an electric guitar for any model please

      • #94248
        Anonymous
        Guest

        hey, i am making a 1958 Goth Gibson Explorer and i have no clue what the measuerments would be, if u know what the measuerments are or have access to some please email them back to me. thx man

      • #93933
        Anonymous
        Guest

        is a strat kit for 150 quid good? email me

      • #84390
        Anonymous
        Guest

        : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job?

        • #106894
          Anonymous
          Guest

          : : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job? Hi 1) I buy all electrical parts and wire them into the guitar.I will be making all my own pickups the winding machine is almost done. 2)It takes me 40 hours to build a eletric threw neck guitar. 3)fretwire,bridge,tailpiece,trusrod,electric parts,tuning keys 4)There a ton of math formulars for this i have templates that fit into a saw that cuts the slots in the correct location.I buy from stewart mcdonalds ,lmi,carvin,wd music ,allparts, About $250.00 can build someones first guitar. 5)They pickup string vibratio using magnets and a eletrical circut. 6)Mostly coming wood working tools a few special ones but not that many.You can buy them from stewart macdonalds 7) Be carefull fingers dont grow back .Study books other guitars find a maker in your area and ask thats what i did.Most of us makers are very giving I have shown two people how to build and one builds a great guitar. Good Luck bick tremontguitars.com

          • #115537
            Anonymous
            Guest

            Battery Limited was established in 1999, Located in Shenzhen, nearby Hong Kong, specializing in producing Nickel Cadmium and Nickel Metal Hydride rechargeable batteries. They are widely used in cordless phones, cellular phones, two-way radios, R/C toys, emergency lightings, power tools, household appliances, office equipments and OEM markets. Now we have more than 2000 employees and have 300,000 producing capacity a day, these products throughout China and many foreign cotntries. website:www.unitechbatt.com email:[email protected] telephone number:86-755-28509555-1063 fax:86-755-28506266 name :mike best price and service thanks a lot

          • #120738
            Anonymous
            Guest

            Hey, i want to build my own guitar, but i havent a clue where to start, i have a good electronics background and would like to chalange myself. Can anyone help? if so E-mail me at [email protected] any plans, tips or suggestions are appriciated, thanks.

          • #107031
            Anonymous
            Guest

            : : : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job? : : Hi : 1) I buy all electrical parts and wire them into the guitar.I will be making all my own pickups the winding machine is almost done. : 2)It takes me 40 hours to build a eletric threw neck guitar. : 3)fretwire,bridge,tailpiece,trusrod,electric parts,tuning keys : 4)There a ton of math formulars for this i have templates that fit into a saw that cuts the slots in the correct location.I buy from stewart mcdonalds ,lmi,carvin,wd music ,allparts, About $250.00 can build someones first guitar. : 5)They pickup string vibratio using magnets and a eletrical circut. : 6)Mostly coming wood working tools a few special ones but not that many.You can buy them from stewart macdonalds : 7) Be carefull fingers dont grow back .Study books other guitars find a maker in your area and ask thats what i did.Most of us makers are very giving I have shown two people how to build and one builds a great guitar. : Good Luck : bick tremontguitars.com Bick do you have any plans or instructions on how to build a guitar from scratch, If you do could you please e-mail them to me, my email adress is [email protected] Thank You Dan

            • #120760
              Anonymous
              Guest

              Hi, can anyone tell me where can I find plans for making a electric guitar on the internet or if anyone could please email me them! Thanks

              • #121887
                Anonymous
                Guest

                : Hi, can anyone tell me where can I find plans for making a electric guitar on the internet or if anyone could please email me them! Thanks

                • #123696
                  Anonymous
                  Guest

                  : : Hi, can anyone tell me where can I find plans for making a electric guitar out of wood on the internet or if anyone could please email me them! Thanks

            • #120744
              Anonymous
              Guest

              Hey, my name is Chris and im from Ottawa, I’m attempting to build a guitar from scratch. COuld anyone email me a design with measurements and what materials i will need. Thanks, my email is [email protected]

            • #112655
              Anonymous
              Guest

              Hi can i have the measurments to make guitars like a virgin, warlock, explorer, flying v or a telecaster?

              • #112875
                Anonymous
                Guest

                : Hi can i have the measurments to make a guitar like a strat?

                • #124127
                  Anonymous
                  Guest

                  : : Hi can i have the measurments to make a les paul junior guitar?

            • #112652
              Anonymous
              Guest

              im 16 and i need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at [email protected] thanks

              • #114887
                Anonymous
                Guest

                : im 16 and i need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at [email protected] : thanks

                • #123978
                  Anonymous
                  Guest

                  I need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at zarco.yon@bol : : thanks

                • #115208
                  Anonymous
                  Guest

                  : : im 15 and i need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at [email protected] : : thanks

                  • #123008
                    Anonymous
                    Guest

                    : : : im 14 and i need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at [email protected] : : : thanks

              • #113665
                Anonymous
                Guest

                i need plans for a cool guitar

              • #113689
                Anonymous
                Guest

                : im 16 and i need plans for an electric guitar that i am about to make, does anyone have any plans? if so please email me at [email protected] : thanks

                • #114161
                  Anonymous
                  Guest

                  i am 16 from vancouver canada and i am intrested into making my own dubble neck guitar if anyone has ideas or a good plan please e mail at [email protected]

            • #112461
              Anonymous
              Guest

              : : : : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job? : : : : Hi : : 1) I buy all electrical parts and wire them into the guitar.I will be making all my own pickups the winding machine is almost done. : : 2)It takes me 40 hours to build a eletric threw neck guitar. : : 3)fretwire,bridge,tailpiece,trusrod,electric parts,tuning keys : : 4)There a ton of math formulars for this i have templates that fit into a saw that cuts the slots in the correct location.I buy from stewart mcdonalds ,lmi,carvin,wd music ,allparts, About $250.00 can build someones first guitar. : : 5)They pickup string vibratio using magnets and a eletrical circut. : : 6)Mostly coming wood working tools a few special ones but not that many.You can buy them from stewart macdonalds : : 7) Be carefull fingers dont grow back .Study books other guitars find a maker in your area and ask thats what i did.Most of us makers are very giving I have shown two people how to build and one builds a great guitar. : : Good Luck : : bick tremontguitars.com : Bick do you have any plans or instructions on how to build a guitar from scratch, If you do could you please e-mail them to me, my email adress is [email protected] : Thank You : Dan

              • #112521
                Anonymous
                Guest

                do u have plans on how to put together pickups from scratch please email me [email protected]

            • #112285
              Anonymous
              Guest

              Hi my name is reece i am 14 and I want to make my own design for a guitar and make it. Can you tell me how to do it from scratch and the materials I will need thankyou.

              • #113114
                Anonymous
                Guest

                Hi im tim and 14 from england, i have built an electric guitar with my dad and we made it out of rosewood, thin steel and PVC sheets(scratch board), if you have your design on your computer send it to me and ill give you some measurements if you want… tim

                • #113984
                  Anonymous
                  Guest

                  : Hi im tim and 14 from england, i have built an electric guitar with my dad and we made it out of rosewood, thin steel and PVC sheets(scratch board), if you have your design on your computer send it to me and ill give you some measurements if you want… : tim

                  • #116065
                    Anonymous
                    Guest

                    hey tim. im sam. im 15 and im from england too! im making a guitar but i dont have the plans on my computer. i’ve taken the measurments off of another guitar but my design for my new one is a bit odd. it looks like the new g-extreme wher the bottom curves in. it looks a bit like: (\ || /) ) ( ( __ ) \/ \/ it is 450mm from top to bottom and about 350mm wide at the widest point. it would be about 250mm from the top of the curve at the bottom to the bottom of the neck. where do my bridge and my saddle need to go? where did you get the plans from the guitar that you made? sam [email protected]

              • #112791
                Anonymous
                Guest

                : Hi my name is reece i am 14 and I want to make my own design for a guitar and make it. Can you tell me how to do it from scratch and the materials I will need thankyou. even if u want to make it from scratch u should buy my own neck.and ued probley ennd to buy some pickups from guitar center or somptin.and id be sure to use a hard wood for the body ,like oak or somptin.c ya.

              • #112370
                Anonymous
                Guest

                i want to make an electric guitar for senior project…anyone want to help? email:[email protected]

                • #112816
                  Anonymous
                  Guest

                  : i want to make an electric guitar for senior project…anyone want to help? email:[email protected] what kind of guitar would u like it to look like.id go with just a fender stratocaster or gibson flying-V myself.

          • #117947
            Anonymous
            Guest

            : : : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job? : : Hi : 1) I buy all electrical parts and wire them into the guitar.I will be making all my own pickups the winding machine is almost done. : 2)It takes me 40 hours to build a eletric threw neck guitar. : 3)fretwire,bridge,tailpiece,trusrod,electric parts,tuning keys : 4)There a ton of math formulars for this i have templates that fit into a saw that cuts the slots in the correct location.I buy from stewart mcdonalds ,lmi,carvin,wd music ,allparts, About $250.00 can build someones first guitar. : 5)They pickup string vibratio using magnets and a eletrical circut. : 6)Mostly coming wood working tools a few special ones but not that many.You can buy them from stewart macdonalds : 7) Be carefull fingers dont grow back .Study books other guitars find a maker in your area and ask thats what i did.Most of us makers are very giving I have shown two people how to build and one builds a great guitar. : Good Luck : bick tremontguitars.com Bick do you have any plans or instructions on how to build a guitar from scratch, If you do could you please e-mail them to me, my email adress is [email protected] Thank You Dan

            • #123248
              Anonymous
              Guest

              hi my name i Jack Blaylock i am 14 and i am doing a chool project of maiking a eletrical guitar, i was wondering if you could send me some information and pictures my adress is: Rindle house burgh-by-sands Carlisle Cumbria England ca56aq if you could it would help me alot Thankyou!

            • #122013
              Anonymous
              Guest

              : : : : I’m 13 years old and am having to do a research paper. I chose to write about how to build an electric guitar. As part of my paper I have to interview several people. Could someone please answer my questions? 1. How do you make and equip the electrical parts and wiring of an electric guitar? 2. How long will it take, how time consuming is it? 3. What are the parts I will need? Where would be the best place to buy parts? 4. How do you measure the frets? 5. Approxiamately, how much will it cost to buy all the parts needed? 6. How do the Pickups pickup the sound the vibrating strings make? 7. What kind of tools am I going to need? Where can I buy these? 8. What is the most important information (knowledge) I need inorder to do a good job? : : : : Hi : : 1) I buy all electrical parts and wire them into the guitar.I will be making all my own pickups the winding machine is almost done. : : 2)It takes me 40 hours to build a eletric threw neck guitar. : : 3)fretwire,bridge,tailpiece,trusrod,electric parts,tuning keys : : 4)There a ton of math formulars for this i have templates that fit into a saw that cuts the slots in the correct location.I buy from stewart mcdonalds ,lmi,carvin,wd music ,allparts, About $250.00 can build someones first guitar. : : 5)They pickup string vibratio using magnets and a eletrical circut. : : 6)Mostly coming wood working tools a few special ones but not that many.You can buy them from stewart macdonalds : : 7) Be carefull fingers dont grow back .Study books other guitars find a maker in your area and ask thats what i did.Most of us makers are very giving I have shown two people how to build and one builds a great guitar. I don’t have an e-mail address and I need the interview NOW. : Thank You Keiaunna

            • #118641
              Anonymous
              Guest

              : : : : i work in a cabinet shop and woodworking is very interesting and challenging to me. ive been trying to teach myself to play guitar, but the guitar i have was my dad’s and is starting to really wear. i think it would be a great challenge to build my own guitar. i have a general idea of how to, but i would like a little assistance. if you could email me some plans and pointers that would be great. thanks alot. shaelum

    • #45187
      Anonymous
      Guest

      Can anyone tell me about sc420? is it really superb?

      • #85674
        Anonymous
        Guest

        : Can anyone tell me about sc420? is it really superb? only if you like punk and heavy mental is the guitar good

        • #90092
          Anonymous
          Guest

          the sc420 rocks…it has sustain for days w/ the wrap around bridge…super smooth: : Can anyone tell me about sc420? is it really superb? : only if you like punk and heavy mental is the guitar good

    • #45186
      Anonymous
      Guest

      I want more info on this model date of issue, value etc. Perfect condition great sound

      • #99365
        Anonymous
        Guest

        what model guitar?

      • #99354
        Anonymous
        Guest

        d

      • #125212
        Anonymous
        Guest

        d

    • #45185
      Anonymous
      Guest

      I bought a pedal(metal zone) a while back, put i can’t seem to get rid of this sort of buzzing sound when i turn on the pedal… I’v tried adjusting everything my amp and the pedal, someone told me i need some other pedal, like a compression sustainer..But i don’t know what thats for…Please Help

      • #107382
        Anonymous
        Guest

        Throw the metal zone in the trash and go buy yourself a PRO CO RAT distortion pedal! Peace

      • #107362
        Anonymous
        Guest

        : I bought a pedal(metal zone) a while back, put i can’t seem to get rid of this sort of buzzing sound when i turn on the pedal… : I’v tried adjusting everything my amp and the pedal, someone told me i need some other pedal, like a compression sustainer..But i don’t know what thats for…Please Help Could be a bad earth on your guitar. If you have single coil p/ups could be them.

      • #84411
        Anonymous
        Guest

        Just try to turn the volume down on your amp, and put the distoration at middle level,while adjusting the EQ, most of the time its the EQ that gives all the trouble, if this donsn’t work then it might be your amp…. And with metal zone you have to really have the patience for getttin the right sound for dist… If your a beginner, metal zone was the wrong buy, a normal cheap dist pedal would have been better, but thats just my opinion…

      • #106898
        Anonymous
        Guest

        : I bought a pedal(metal zone) a while back, put i can’t seem to get rid of this sort of buzzing sound when i turn on the pedal… : I’v tried adjusting everything my amp and the pedal, someone told me i need some other pedal, like a compression sustainer..But i don’t know what thats for…Please Help HI Here`s an idea don`t get mad at me Put the pedals aside and get all you can out of your amp and guitar first.I have playing a long time 20 years im old LOL I still don`t use a effect execpt reverb thats only at home live no way.People still laugh at first but not long .I learned this from a guitar teacher when I was 14 to 17 he was not a fan of effects until you master the guitar .He died in a motor cycle crash last year .He was the best guitar player I new personly and taught me this lesson.Please spend time playing clean or with the amps natual distition the results last a life time. Bick tremontguitars.com

      • #84409
        Anonymous
        Guest

        Right now all i use is my delay pedal, i was asking around for a better Metal kinda sounding pedal, cuz metal zone give WAY TO MUCH FEEDBACK…..

        • #106925
          Anonymous
          Guest

          Me 2 : Right now all i use is my delay pedal, i was asking around for a better Metal kinda sounding pedal, cuz metal zone give WAY TO MUCH FEEDBACK…..

      • #106877
        Anonymous
        Guest

        I’m not sure how to explain it.A compressor keeps the signal from either "peaking"(being too loud) or "diving"(being to low).It keeps everything even,tight. METAL ZONE-the buzzing is an common problem with that pedal.The E.Q. section is too sensitive and needs to be re-tweaked if you change amps.I don’t like them much,but that’s just me.It has lots of gain,try keeping the dist.level down. You might want to try something easier to dial.I have a Smash-Box that I love.It does ONE thing,distortion!Just keep it clean. The RAT is great and I heard a lot of good stuff about the Digitech HOT ROD Dist.Music shops seem to like ’em…?? There are other decent ones. Hope this helps

    • #45184
      Anonymous
      Guest

      Both are great guitars..but kh-2 is bolt-on. Wich one should i buy? Sorry for my shitty english

      • #102807
        Anonymous
        Guest

        RR-1 is american made and will play better than a lot of guitars that cost twice as much as it. And as usual ESP will be pretty crappy.

    • #45182
      Anonymous
      Guest

      People, I need to know the difference between a chrome cover humbucker and a open one, i want a pickup that gives good cruch and dont keep ringing when i palm mute, can any one help me?

      • #107355
        Anonymous
        Guest

        : People, I need to know the difference between a chrome cover humbucker and a open one, i want a pickup that gives good cruch and dont keep ringing when i palm mute, can any one help me? The chrome covers are there just to make them look nice, they also block your signal. I would go for S/Duncan "Pearly gates" or a "Jeff beck JB1". Ive used both of these and they both sound great.

      • #106884
        Anonymous
        Guest

        Chrome or open doesn’t really matter. Look towards a good Duncan or Dimarzio. You can go to their websites and compare attributes.

    • #45183
      Anonymous
      Guest

      People, I need to know the difference between a chrome cover humbucker and a open one, i want a pickup that gives good crunch and dont keep ringing when i palm mute, can any one help me?

    • #45181
      Anonymous
      Guest

      People, I need to know the difference between a chrome cover humbucker and a open one, i want a pickup that gives good crunch and dont keep ringing when i palm mute, can any one help me?

    • #45180
      Anonymous
      Guest

      i have – roland Gi 10 /gk2a, 2 jensen speakers c12r, lee jackson perfect connection, tascam 414 portastudio,boss dr550,fender single alnico, set of 3 Jackson pickups H-S-S

      • #92159
        Anonymous
        Guest

        Do you still have your GI-10? I have some gear for trade or will buy. markb111 at hot mail or markusb 111 at ya hoo : i have – roland Gi 10 /gk2a, : 2 jensen speakers c12r, lee jackson perfect connection, : tascam 414 portastudio,boss dr550,fender single alnico, set of 3 Jackson pickups H-S-S

      • #95218
        Anonymous
        Guest

        I’m inerested in gi-10 + pickup. what is the condition and asking price?

      • #101377
        Anonymous
        Guest

        i am interested in the tascam 414 portastudio can you email me? [email protected] Cheers kat

      • #118571
        Anonymous
        Guest

        still have the gi-10? if so, would you sell it alone? if so, how much?

      • #93482
        Anonymous
        Guest

        Do you still have any MIDI guitar gear? I’d like to get the Roland GK2A and the GI-10 or equivalents. Let me know what you needs are as well… RYUN : i have – roland Gi 10 /gk2a, : 2 jensen speakers c12r, lee jackson perfect connection, : tascam 414 portastudio,boss dr550,fender single alnico, set of 3 Jackson pickups H-S-S

    • #45179
      Anonymous
      Guest

      Korg A5 Guitar effects pedal

      This popular thread has been given its own page : Korg A5 Guitar effects pedal

    • #45178
      Anonymous
      Guest

      i want to start playing either an eletric guitar or an ecoustic, what cheap prices should i be looking for and witch gutair would you recormend for me

      • #84405
        Anonymous
        Guest

        I’d say start with the one you enjoy the most.Have fun,it’ll keep you motivated,you can always pick up the other one later. Guitars?? Hmm,$200.-$350. is about right.Squire(Fender),Epiphone makes decent stuff.Ibanez and Fernandez also.I’d stay away from locking tremelos for now. If you get a used guitar,make sure there isn’t a lot of fret wear and the neck is straight. Good Luck

    • #45174
      Anonymous
      Guest

      I HAVE BEEN LOOKING FOR THE YEAR AND HOW MUCH MY FENDER STRATOCASTER IS WORTH I CANT SEEM TO FIND IT ON ANY SITE THE SERIAL NUMBER IS MN427145 IF YOU CAN HELP ME PLEASE E-MAIL ME AT [email protected] THANK YOU

    • #45177
      Anonymous
      Guest

      Does anyone out there know how to switch the locations of the preset patch sounds on a Boss ME-30? I lost the owner’s manual and I can’t figure out what to do without losing other preset sounds. I would really appreciate the help, I just want to put three sounds I use on the same bank instead of doing a tap dance to get to each one. Thanks.

      • #100426
        Anonymous
        Guest

        : Does anyone out there know how to switch the locations of the preset patch sounds on a Boss ME-30? I lost the owner’s manual and I can’t figure out what to do without losing other preset sounds. I would really appreciate the help, I just want to put three sounds I use on the same bank instead of doing a tap dance to get to each one. Thanks. u push the copy button next to the edit and choose the bank u want to put them in….

        • #112770
          Anonymous
          Guest

          is there a clean effect or function on the ME-30, i can’t find a bank with one in it. I bought mine used and im so lost because there is no owners manual. If anyone has a link to an owners manual for this ungodly piece of machinery then PLEASE GIVE IT TO ME.

    • #45175
      Anonymous
      Guest

      I am trying to find some plans and instructions for building an electric guitar. Not any kits i want to make one out of scratch. thanks.

      • #100087
        Anonymous
        Guest

        : I am trying to find some plans and instructions for building an acoustic guitar. Not any kits i want to make one out of scratch. thanks.

      • #102278
        Anonymous
        Guest

        : i need help, I am trying to find some plans and instructions for building an electric guitar, as i need to do one for a school project so i have to do it from scratch thanks.

      • #82907
        Anonymous
        Guest

        : I am trying to find some plans and instructions for building an electric guitar. Not any kits i want to make one out of scratch. thanks.

        • #87149
          Anonymous
          Guest

          : I am trying to build an electric guitar and i was wondering if you can send me plans and informatioin on how to build them.

      • #103940
        Anonymous
        Guest

        fuck wheres the damn follow ups i need this too

        • #116021
          Anonymous
          Guest

          What the fuck is goin on. I can’t see the follow ups. I think this site sucks.

    • #45176
      Anonymous
      Guest

      A while ago I lost my footswitch, and I’m already tired of changing channel pressing the button on my combo and I don’t whant to buy another footswitch. My amplifier is a Marchall Valvestate VS-65R. Does somebody have a schematic of a footswitch marchall of one button?

      • #92560
        Anonymous
        Guest

        : A while ago I lost my footswitch, and I’m already tired of changing channel pressing the button on my combo and I don’t whant to buy another footswitch. My amplifier is a Marchall Valvestate VS-65R. Does somebody have a schematic of a footswitch marchall of one button? Hi ! I repaired a footswitch an hour ago. In what format do you want the schematic?

    • #45172
      Anonymous
      Guest

      i own 2 electro harmonix cabs .and i use a crate head .these things sound awsome "like the bloodthirst album by cannibal corpse" but really i was wondering if any body knows anything about these .there russian, russian soft pine , and unfinished "look really cool" but im interested in them . what should i know about these

    • #45173
      Anonymous
      Guest

      okay, this is gonna seem like a really dumb and pointless question, but i’m just curious. i have a ’96(roughly) squier stratocaster. it’s a mik, and i was wondering what kind of wood the body would be made out of. i can’t seem to find this information anywhere, so anyone who could help me out, that’d be great. thanks a lot! dano

    • #45169
      Anonymous
      Guest

      plzzzzzzzzzzzzzzzzzz try to send guitar pro 4 crack to my email [email protected] thxxxxxxxxxx very much

    • #45170
      Anonymous
      Guest

      plzzzzzzzzz i need a crack for guitar pro 4, try to sand it to me if you can on [email protected]

    • #45171
      Anonymous
      Guest

      Has anyone got this book? Did you learn the techniques in a short time? Do you recommend this book? I’d like to get some opinion if this is worth keeping. Thank you. Angel

      • #94616
        Anonymous
        Guest

        Hey!! Im thinking of buying this book too a year later. is it good? are you as good as it said you would turn out to be? is it worth buying? if you could get back to me that would be cool! thanks Rory

    • #45167
      Anonymous
      Guest

      I have an old cutaway elec/acoustic Hohner.(leyanda line) When I plug it into the desk I get no signal.Ther does not seem to be any battery power in the guitar. Do I need to use phantom power on the desk?

    • #45168
      Anonymous
      Guest

      I’m da best!!!

      • #84407
        Anonymous
        Guest

        The next best thing!!!

    • #45164
      Anonymous
      Guest

      1969 Hernandis No. 1 classical guitar.

      This popular thread has been given its own page : 1969 Hernandis No. 1 classical guitar.

    • #45163
      Anonymous
      Guest

      Does anyone have information regarding the present day value of a Framus acoustic guitar, serial # 16039 model 5-34? The guitar was manufactured in Bavaria.

    • #45166
      Anonymous
      Guest

      get a hendrix backing track player free at http://guitartuner.20m.com

      • #107102
        Anonymous
        Guest

        : get a hendrix backing track player free at http://guitartuner.20m.com Dont bother it u want it for recording cause its midi files and sounds shite

    • #45165
      Anonymous
      Guest

      where can i find dimebags tattoos

      • #85322
        Anonymous
        Guest

        all over him…lol

    • #45162
      Anonymous
      Guest

      Do you guys have an idea what portable midi device (no laptop) can i use for taking my processor’s presets with me all the time when touring? Just in case a factory reset is needed and i have to bulk dump my presets back to my processor? Thanx Robert

    • #45160
      Anonymous
      Guest

      Hi everybody and thanks for at least trying to help me…i want to adjust my harmonics on my guitar that has a floyd rose tremolo…lets say the 6th E is 440hz open but at the 12th fret its sharp a little…i know i have to adjust it so the string is longer but how? thank you very much…would anybody know where i could find reliable boss gt-3 patches…thx

      • #96650
        Anonymous
        Guest

        There is an actual article on adjusting Floyd Rose floating bridges on http://www.guitarnoise.com/guitar/tuning/

      • #84396
        Anonymous
        Guest

        It should be the A string that is at 440. Here’s what you do. Tune each string. Next, start with the low E string and fret it at the 12 fret. If it is sharp then you need to move the saddle back…if flat you need to move it forwards. You can do that by loosening the string, loosen the allen screw that sits in front of the saddle, then move the saddle in the appropriate direction. Thighten everything and retune. Check again at the 12 fret. Repeat the process as necessary. Move on to the next string. Later

    • #45159
      Anonymous
      Guest

      Hi All, My Dad wants a GT5. He is in India. He is not a very advanced Guitar player. I couldn’t afford a GT5 for $500 or $600. Is there any alternative system available to buy below $200 ? He is looks for a system that will sync Violin, Sitar, Veena like instruments. Thanks for the help.

      • #93930
        Anonymous
        Guest

        your dad should keep to playing an acoustic.. i cant beleive this was the first fucking result that came up after searching.. "BOSS GT-5 purchase" in google.com

    • #45161
      Anonymous
      Guest

      Anybody have one for sale…please contact me. Thanks!!!

      • #95250
        Anonymous
        Guest

        i nhave ine that is lacquer not burst, but sounds amazing. jeremy : Anybody have one for sale…please contact me. : Thanks!!!

    • #45157
      Anonymous
      Guest

      I have a ’64 Gibson Melody Maker (double cutaway) and the original tailpiece is in bad shape. I’m looking for a tailpiece/bridge that will install on the original postbolts. I DON’T want to modify this ax anymore than necessary, but don’t care for the string rattle etc with the original tailpiece. I’ve heard the Badass Bridge will do the trick. Is this certain and are there others that will attach using the original bolts? Thanks in advance for your help.

      • #84914
        Anonymous
        Guest

        : I have a ’64 Gibson Melody Maker (double cutaway) and the original tailpiece is in bad shape. I’m looking for a tailpiece/bridge that will install on the original postbolts. I DON’T want to modify this ax anymore than necessary, but don’t care for the string rattle etc with the original tailpiece. I’ve heard the Badass Bridge will do the trick. Is this certain and are there others that will attach using the original bolts? Thanks in advance for your help. Hello, I have an early 60’s MM and had the Badass bridge installed. It fit perfectly. Hope this helps. Daryl

    • #45158
      Anonymous
      Guest

      Can anyone tell me what they think is the keyword/s for "The Love of guitar numerology?"

    • #45155
      Anonymous
      Guest

      CAN ANYBODY GIVE ME A SITE TO VISIT FOR NEW PATCHES FOR MY ZOOM 606 GFX I REALY NEED SOME! FROM THE SHADOWS TO SLIPKNOT! YOURS STEVE.

      • #85037
        Anonymous
        Guest

        under construction

    • #45156
      Anonymous
      Guest
      • #98882
        Anonymous
        Guest

        EMG 81 sound geart in that type of body … I think Guitarist Eddie Sash uses them. http://www.soundclick.com/bands/4/eddiesash.htm

      • #98861
        Anonymous
        Guest

        EMG 81 sound geart in that type of body … I think Guitarist Eddie Sash uses them.

      • #84282
        Anonymous
        Guest

        I have a ESP Ltd-f-200 with a basswood body, with two emg-81s, and it sounds sweet… utterly sweet hehehe 🙂 very good harmonics, added a lot of sustain. Seems like it made it a bit more bassy with clearer treble, but not scratchy. Perfect for anything heavy. Also very nice cleans, as before lots more bass in the cleans. Hope that helps. Email me if you want more help.

    • #45153
      Anonymous
      Guest

      hi do you know where can i fined cheap Celestion Gold Back 100W R.M.S 16 ohm 12" speakers ? thanks

    • #45154
      Anonymous
      Guest

      Does anyone have any info on the series of sitars Danelectro put out with the serial # 8010? Have been searching withour success since 1999. The web has yielded nothing!! It’s not consistant with the usual line of Danelectro Sitars…HELP!!

    • #45152
      Anonymous
      Guest

      I am looking to buy a new geet, quite an inexperienced player, but getting better!!! I think have been reading lots of reviews, forums etc and have had a quick play of an Epi LP Custom – Can anyone explain where the differences are between the 3 models, or is it just a quality difference. Also any opinions on the Goth LP Studio? Cheers

      • #84417
        Anonymous
        Guest

        alright mate, here ya go. the Epi lp studio, i think, has a bolt on neck, and is in general a pretty low quality instrument. next step up, the standard. it’s a good guitar, set neck, binding. i had one a few years back, and it treated me well. then you have the custom. asstetically, a beautiful guitar. but when it comes down to it, it’s the same set up as a standard, set neck, same pu’s. but, it is a great looking guitar that plays well. now personally, i’d steer clear of the goth lp. actually, my advice to you is, if you have the money, get a gibson lp studio, or if you really want an lp but don’t have the money, save for one. i have a ’96 gibson studio, and i wouldn’t trade it for the world. great great great guitar. now, you said you don’t have much experience, so you’d probably wanna look at a more inexpensive model(which kinda defeats the purpose of the gibson studio, but i figured that guitar gets knocked down enough, so i needed to stand up for it :)} might i suggest a mid 90’s squier? now hear me out. the guitars squier makes now, i think, are piss-poor instruments. however, the ones they made in the mid 90’s, though not of american quality, are still really good guitars. that’s what my first guitar was, a ’94 squier. still have it, and still use it. so those are my suggestions to you, mate. if you’ve anymore questions, please, feel free to email me, i love talkin’ guitars! peace out. dano

        • #123700
          Anonymous
          Guest

          Hey that other guy was full of shit. I have a epiphone les paul and my uncle used to have a standard gibson. the studio les paul doesn’t have a maple body cap and has a less richer tone than the standard. in my opinion my epiphone sounds great and i even prefer it over the gibsons. the only problem with them is fret buzz but with the right adjustments you could get rid of it although the pickups are so good they don’t pickup the buzz. And If you decide to go with a squire get the new squire 51 it is a combination between a strat and a tele IT IS FRICKING AWSOME it is a well made gouitar and you get A LOT of bang for your buck. the only flaw in this guitar is some slight intonation problems in the upper frets but it is very little and can be corrected with the right adjustments to the saddle.

    • #45150
      Anonymous
      Guest

      im desperately looking for these kinds of guitars!

      • #89483
        Anonymous
        Guest

        Hey Zack, If you’ve located an Ultrasonic already, Have you got any leads? I’d like one as well! I’m a player, no dealer! Big Who fan, I’d like one in sunburst, any ideas?

      • #87104
        Anonymous
        Guest

        : im desperately looking for these kinds of guitars!

        • #87258
          Anonymous
          Guest

          I have one of these and would be interested in selling

    • #45151
      Anonymous
      Guest

      Hi everybody, I’m looking for a Fender HM Strat ’87/’88 with a maple fingerboard, like the one used by mr.Greg Howe, doesn’t matter the color though (pink, white, plumb, etc). If you have one in good shape for sale, let me know…Ah! I forgot, I’m from Italy! Bye…

      • #87099
        Anonymous
        Guest

        I have a near mint hot pink/raspberry ’88 Fender HM Strat for sale. It’s got rosewood/maple neck and DiMarzio Dual Sound humbucker/Fender Single/Fender Single. New black Gotoh tuners and black nut string clamps. $400 plus shipping with Fender Hardshell case. E-mail me if interested and I have photos.

      • #87119
        Anonymous
        Guest

        : Hi everybody, I’m looking for a Fender HM Strat ’87/’88 with a maple fingerboard, like the one used by mr.Greg Howe, doesn’t matter the color though (pink, white, plumb, etc). If you have one in good shape for sale, let me know…Ah! I forgot, I’m from Italy! Bye…

        • #95839
          Anonymous
          Guest

          I have one for sale. its in a good condition. dimarzio double, F.single, F.single. kahler usa tremolo, gotoh keys, maple neck. i sell it for 800 Chf i am from switzerland. please answer

    • #45149
      Anonymous
      Guest

      I have seen humidifiers that hang inside an acoustic sound hole, but I also have a semi acoustic (ibanez) with f holes. Any ideas about humidification (good word) of the guitar or the room? Ta Fred

    • #45148
      Anonymous
      Guest

      I am interested in purchasing a messaboogie amp. Please contact me with information as to where or whom I can purchase this from [email protected]

      • #84318
        Anonymous
        Guest

        : I am interested in purchasing a messaboogie : amp. Please contact me with information as to where or whom I can purchase this from : [email protected]

    • #45147
      Anonymous
      Guest

      I GOT A WASHBURN HM-5V guitar from the mid to late 80’s and the headstock broke where the low E key is. The neck is wider at the joint than necks are now.I believe it’s 2.5" at joint. I was wonering if anybody has or has had a similar Washburn with a v-neck and if they had the same break point. I also would like to know where to get a replacement if any.

      • #87445
        Anonymous
        Guest

        : I GOT A WASHBURN HM-5V guitar from the mid to late 80’s and the headstock broke where the low E key is. The neck is wider at the joint than necks are now.I believe it’s 2.5" at joint. I was wonering if anybody has or has had a similar Washburn with a v-neck and if they had the same break point. I also would like to know where to get a replacement if any. I have/had the HM-5V and am also looking for a replacement neck. I have a guy who will build one custom for me, but don’t have the heel size. It was a great guitar and I would love to get it rebuilt.

    • #45146
      Anonymous
      Guest

      im desperate for some new patches for my zoom 606, if anyone can give me a site to visit or any info on where to find some please e-mail me yours steve. (from shadows to slipknot!)

      • #108119
        Anonymous
        Guest

        : im desperate for some new patches for my zoom 606, if anyone can give me a site to visit or any info on where to find some please e-mail me : yours steve. (from shadows to slipknot!) http://www.aspecto.net/zoom606/indexe.asp This is the only one I know of. It’s pretty new so there aren’t that many, but it’s a start aint it!

      • #85993
        Anonymous
        Guest

        What effects pedals does jack white use? Please dont say he doesn’t use any because he does! I know he gets the blusy tone from the sears amp and his unique guitar but he uses a distortion pedal as well as, i think, an effects unit to get that bluesy grainy sound. Any guesses? Could i get that effect through a zoom 606 effects pedal?

        • #99003
          Anonymous
          Guest

          jack uses a jeckyl/hide overdrive-distortion pedal, to get that crunchy gain distortion, and in teh elephant album, for the bass lines uses a digitech whammy effect, that detunes 1 octave the guitar, and for the solos just a metal slide.

        • #90461
          Anonymous
          Guest

          : What effects pedals does jack white use? Please dont say he doesn’t use any because he does! I know he gets the blusy tone from the sears amp and his unique guitar but he uses a distortion pedal as well as, i think, an effects unit to get that bluesy grainy sound. Any guesses? Could i get that effect through a zoom 606 effects pedal? As far as i know he uses at least the following pedals. An electro-harmonix USA Big muff for distortion, a digitech whammy for octave shifts, and a boss cs3 as his sustainer. Im not too sure that the boss one is correct but im fairly positive the other 2 are. The big muff distortion pedal gives alot of feedback if you stop playing while its one, but i guess thats a rather obvious attribute of the white stripes sound.

    • #45145
      Anonymous
      Guest

      I have a one year old Fender Strat that I was using Ernie Ball, Heavy Top Skinny Bottom strings on since I’ve had it. I just recently switched to some 9-42 light strings, and they buzz like a bee hive. I’ve adjusted action, I’ve adjusted the truss rod, and nothing will get rid of the buzzing. I play with a hard touch, but it seems ridiculous to not be able to get rid of the buzzing, even with the action all the way up and the truss got as loose as it goes. The buzzing even goes through to the amp, and power chords sound very muddy and unpronounced compared to before. Does anyone have any idea what’s happening here? I would really appreciate any help anyone could offer.

      • #82073
        Anonymous
        Guest

        Well, Eric. I think your main problem is that the strings are metal. you should really think about investing in some strings made out of twine, it really stops the buzz. You could also think about rubbing margrine on the neck and grease things up.. you will get a lot smoother sound.

    • #45144
      Anonymous
      Guest

      hi I’m currently a bass playing, and I’m wondering what is the difference between a touch and stick guitar, and how do you play them? Thanks

    • #45143
      Anonymous
      Guest

      recently someone in canada contacted me about their vox ultrasonic, i think his name was dan, but ive recently lost hi email and desperately want to purchase this guitar from him! he aslo sent me a picture of his son with it! if you are this person PLEASE CONTACT ME!

      • #94811
        Anonymous
        Guest

        send me some pics if you still want to sell

      • #87438
        Anonymous
        Guest

        hey man, that was me, get in touch if you are still interested. Dan : recently someone in canada contacted me about their vox ultrasonic, i think his name was dan, but ive recently lost hi : email and desperately want to purchase this guitar from him! he aslo sent me a picture of his son with it! : if you are this person PLEASE CONTACT ME!

        • #115718
          Anonymous
          Guest

          : hey man, that was me, get in touch if you are still interested. : I have a picture off my son with my vox ultrasonic : : recently someone in canada contacted me about their vox ultrasonic, i think his name was dan, but ive recently lost hi : : email and desperately want to purchase this guitar from him! he aslo sent me a picture of his son with it! : : if you are this person PLEASE CONTACT ME!

    • #45142
      Anonymous
      Guest

      thats basically it….i am to the experienced side of beginner and i just confused myself by trying to figure out if its better to always pick up down up down regardless of which strings you are hitting….

      • #106883
        Anonymous
        Guest

        Yes!! At this point in your gutitar playing learn how to do things correctly.Develop good habits NOW!! Later on you’ll come across things that can’t be hammered or slurred. "Learn the Rules BEFORE you Break them". Good Luck

      • #84276
        Anonymous
        Guest

        No it’s not. Your stroke depends on what you’re trying to accomplish. It’s a good skill to master in order to solo well and play with a faster attack.

    • #45140
      Anonymous
      Guest

      I want to put nylon strings on steel string guitars, but I want to make sure that the guitar will work properly. Can you tell me what modifications, if any, I need to make on the various types of guitars: acoustic, acoustic-electric, solid body, etc? Will the string pick up OK? Thanks

    • #45141
      Anonymous
      Guest

      Hello, if somebody are interest to purchase the following guitars, please contact me. Sincerely Fernando Ponce de León. http://www.fleta-kohno.8k.com fleta: more than u$20.000 kohno: more than u$2.000 [email protected] I am selling in 30 days

      • #86956
        Anonymous
        Guest

        I sent you a separate email already with my questions to [email protected]. I am interested in the fleta. James McGill : Hello, if somebody are interest to purchase the following guitars, please contact me. : Sincerely : Fernando Ponce de León. : http://www.fleta-kohno.8k.com : fleta: more than u$20.000 : kohno: more than u$2.000 : [email protected] : I am selling in 30 days

      • #84853
        Anonymous
        Guest

        Hi! I want to buy the kohno. still have it? please let me know Which is the best price? thanks Marian : Hello, if somebody are interest to purchase the following guitars, please contact me. : Sincerely : Fernando Ponce de León. : http://www.fleta-kohno.8k.com : fleta: more than u$20.000 : kohno: more than u$2.000 : [email protected] : I am selling in 30 days

      • #84439
        Anonymous
        Guest

        Hi Fernando! I am very, very interested in the Kohno guitar, i would buy the instrument, but a problem is the transportation. And how much money do you exactly want for the instrument? I have already written you two E-mails to two different adresses (ferponce and webmaster), i hope I get a response soon!! Sincerely Dominik Hoffmann

        • #84578
          Anonymous
          Guest

          Hi Dominik Hoffmann!! I send you an e mail but you cant recive e-mail from "msn.com", please tell me other e mail acount. I get yours emails but I cant reply fernando

          • #107071
            Anonymous
            Guest

            Hi Fernando! I get your E-mail yesterday, yes you can write me e-Mails from the adress [email protected]! I can get them now! So I wrote you an E-mail yesterday, I think you got it. If not, tell me here! Dominik

            • #114757
              Anonymous
              Guest

              if you are interested in buying a topnotch kohno (’80/model 20) let me know. db

Viewing 221 reply threads
  • You must be logged in to reply to this topic.