: Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected].
Could you supply me with a schematic?
The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
: : Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
: Could you supply me with a schematic?
: The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
: : Hi. I need a schematic for a Marshall 200 Bi-Chorus valvestate. Please contact me at [email protected]
: Could you supply me with a schematic?
: The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
I can not live another day without schem. for a DOD FX55-c Supra distortion pedal. if you have it, or know where it is; don’t hesitate to tell me and i will be forever in your debt.
-Jilane S.-
Does anyone have the Boss PH-2 Super Phaser Schematic? The problem I’m experiencing has to do with the power source when used with an adapter. It works fine with a battery but won’t run right using a 100mA or 200mA DC power source. Weird, it seems to need more power then it should when it’s bypassing the battery.Please Help if you can.Thanks alot
: Hello
:
: I have a 5 knob Deluxe Memory Man with MN3005’s. Now i just opened it up and had a look at a schematic, here is what i have noticed on the PCB board.
:
: 1. 2x MN3005 and one spare socket
: 2. 5x 4558
: 3. 1x NE570
: 4. 1x 5087
: 5. 5x Trim Pots
: 6. 1x 4047
:
: The MN3005’s are located on the top left of the PCB and the spare socket is the socket on the far left. And the two MN3005 are located to the right of that, under the three sockets are trim pots with a trim pot between the far right socket and the middle one
: Now i am assuming that there is one MN3005 missing??
:
: If anyone has a picture of the the PCB could you please post it, or even a schematic, i have look at one schematic but it had more NE570’s etc…
:
: Regards
It is just normal. EH have built somme Delay with a third MN3005 Socket but normal are 2 MN3005. Maybe you can but a third BBD Chip inside to enlarge your delay time up to 615ms.
Re: This popular thread has been given its own page :... Andrew
Andrew
Hello
I have a 5 knob Deluxe Memory Man with MN3005’s. Now i just opened it up and had a look at a schematic, here is what i have noticed on the PCB board.
1. 2x MN3005 and one spare socket
2. 5x 4558
3. 1x NE570
4. 1x 5087
5. 5x Trim Pots
6. 1x 4047
The MN3005’s are located on the top left of the PCB and the spare socket is the socket on the far left. And the two MN3005 are located to the right of that, under the three sockets are trim pots with a trim pot between the far right socket and the middle one
Now i am assuming that there is one MN3005 missing??
If anyone has a picture of the the PCB could you please post it, or even a schematic, i have look at one schematic but it had more NE570’s etc…
This group discussion is dedicated to Pure Ambient Space Landscape Music.
To give Ambient Artist exposure due them and their music.
And to promote these talented artist and their Recording Label’s.
And to keep the fan’s in touch with the favorite artist e.g. (latest recordings, labels, concerts etc.). And allow there fans to speak out and discuss their ( artist ) music tracks and styles.
the_ambient_way-subscribe@yahoogroups
Rhea Cary Owner
Hope to hear from you. and please pass on the word to others who might be interested.
oi!
For switching, you’ve got many solution. Passive one, with switch, but not very easy and good look, and active. For active, you can use the 4066 CMOS chip. They are very cheap, try to get the
datasheet (easy to find), it’s 4 digital controled analog switch. Marshall in the VS100 use somme of them. But they’ve got bad dynamics. They are many version f this cheep, look for them. They are also
a way, like the Mesa V-Twin (www.scheamticsheaven.com) with FET, I never try this. And the last solutin, wich is most use in Mesa and rivera amp, it’s to use LDR. look at mesa dual rect!
: looking anywhere from 1 second and up if you have any please let me know..thankx
easy….
an ADC, DAC and memory…
A clock to make the whole thing work, and gooo!! Cheap!
If you want more, I’m working on a cheap multiFX processor… (so with very long delay, sampler!)
I desperately need a schematic for an original Maxon D&S II distortion box. Or, better yet, can someone just tell me
where to reconnect the battery leads?
hi,need the manual for the casio mg 510 midi guitar.Also,i’mlookin’for the schmatics of some enhancers,like the boss pedal or,better yet,the BBe stinger.Any help?thnks
: hi,need the manual for the casio mg 510 midi guitar.Also,i’mlookin’for the schmatics of some enhancers,like the boss pedal or,better yet,the BBe stinger.Any help?thnks
My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
: My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
The tubes just need to warm up like every other tube product!!
Re: This popular thread has been given its own page :... pilo
pilo
: My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
I think it’s a problem of the power voltage.
If you have a voltmeter, plug it on the tube power, and see if when the sound go down the volatge go down. If it’s that, It may come in the power supply. Do you change it? or juste try? And what did you test? it may be a capacitor problem.
: I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
joerg
mrbill:
does anyone have hk schematics? I have an original tubeman and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
: hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
: joerg
: mrbill:
: does anyone have hk schematics? I have an original tubeman and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
: : hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
: : joerg
: : mrbill:
: : does anyone have hk schematics? I have an original <b style="color:black;background-color:#ffff66">tubeman</b> and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : : I need Hughes & Kettner <b style="color:black;background-color:#ffff66">tubeman</b> <b style="color:black;background-color:#a0ffff">plus</b> schematics. Can anyone help me?
: : : hi, i just purchased a used <b style="color:black;background-color:#ffff66">tubeman</b> <b style="color:black;background-color:#a0ffff">plus</b>. but without schematics? have you got a schematic???
: : : joerg
: : mrbill:
: : does anyone have hk schematics? I have an original <b style="color:black;background-color:#a0ffff">tubeman</b> and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : : I need Hughes & Kettner <b style="color:black;background-color:#a0ffff">tubeman</b> <b style="color:black;background-color:#99ff99">plus</b> schematics. Can anyone help me?
: : : hi, i just purchased a used <b style="color:black;background-color:#a0ffff">tubeman</b> <b style="color:black;background-color:#99ff99">plus</b>. but without schematics? have you got a schematic???
: : : joerg
I have been recently hired in a repair shop that specializes in Guitar Amps…they have a bad backlog of vox amps and would like links files or help finding inexpensive schematics to help me catch up on the work…I appreciate all help in this matter
Hey, I need schematics of the following effects: BOSS Metal Zone MT-2, BOSS OverDrive OD-3, BOSS Digital Delay DD-5 and BOSS Distorsion DS-1. As you can see´I´m a very big fan of the BOSS effects. Please if you can find them send them to me. Thanks a lot!!
I HAVE A DIGITECH GSP 21 AND HAVE A PROBLEM WITH THE NOISE GATE. IF I TURN IT OFF IT STAYS ON AND CLIPS THE SIGNAL IF IT DOESNT REACH A CERTAIN LEVEL. IF ANYONE CAN HELP, PLEASE LET ME KNOW WHERE I CAN FIND A SCHEMATIC ON LINE OR HELP WITH MY PROBLEM.
Mine’s broken too, but maybe you could have a look at yours and tell me where the "hot" wire to the Comp socket comes from on the PCB – just tell me what component(s) share the track.
Here’s a few things you should check for:
15-0-15 Vac at the transformer secondary
+25 volts across the smoothing capacitor
check that the LED isn’t blown (it’s in SERIES with the Vcc line to the rest of the pedal – try shorting it out and see if your pedal comes to life).
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shematic! Will we change?
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shenatic! Will we change?
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shenatic! Will we change?
I scored one for 5 bucks, but cant get the infinite loop to work (LED doesn’t light, no effect). Anyone know possible cause offhand, or could point me towards a schematic? Thanks!
I need a shematic for a jimi hendrix (jim dunlop)wha wha, model jh-1.
I want to increase the low end frequancy response and need to know what caps i need to change out……….thanks , Ray
I am looking for an effect switcher schematic;passive is ok or active
is alright .It would be used to switch multiple effects in and out ,and to
switch to multiple amps.I would like to learn to do it like the pro’s do.
Any help would be greatly appreciated.
charles phillips [email protected]
rock on
: I am looking for an effect switcher schematic;passive is ok or active
: is alright .It would be used to switch multiple effects in and out ,and to
: switch to multiple amps.I would like to learn to do it like the pro’s do.
: Any help would be greatly appreciated.
: charles phillips [email protected]
: rock on
oi!
For switching, you’ve got many solution. Passive one, with switch, but not very easy and good look, and active. For active, you can use the 4066 CMOS chip. They are very cheap, try to get the datasheet (easy to find), it’s 4 digital controled analog switch. Marshall in the VS100 use somme of them. But they’ve got bad dynamics. They are many version f this cheep, look for them. They are also a way, like the Mesa V-Twin (www.scheamticsheaven.com) with FET, I never try this. And the last solutin, wich is most use in Mesa and rivera amp, it’s to use LDR. look at mesa dual rect!
Help Please i need scematics for all types of pick-ups and volume and tone control and switch choosing thanks.
This popular thread has been given its own page : Marshall Valvestate 8280 bi chorus schematic
Hi,i need a schematic diagram Marshall valvestate 8082 bi chorus
: thanks
DEAR MARSHLL VAILLA I WOULD TO MEET YOU ON SUNDAY AT PETERBROUGH SALVATION ARMY FROM JAMES COLEMAN
: thanks
: Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected].
Could you supply me with a schematic?
The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
: thanks
: : Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
: Could you supply me with a schematic?
: The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
: : thanks
: : Hi. I need a schematic for a Marshall 200 Bi-Chorus valvestate. Please contact me at [email protected]
: Could you supply me with a schematic?
: The amp seem to have low volume, I suspect the pre-amp section. Do you know if the single valve in the circuit is part of the pre-amp stage?
: : thanks
: Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
: thanks
: Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
: thanks
Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
thanks
I can not live another day without schem. for a DOD FX55-c Supra distortion pedal. if you have it, or know where it is; don’t hesitate to tell me and i will be forever in your debt.
-Jilane S.-
please send-my the vs 100 schematic diagram.thanks!
Does any one have a schematic for the Fulltone Distortion Pro?
Thanks Ed
Please send me the schematic diagram of BOSS Metalzone.
Thanks
I need a tube screamer shematic or some thing similar.
Does anyone have the Boss PH-2 Super Phaser Schematic? The problem I’m experiencing has to do with the power source when used with an adapter. It works fine with a battery but won’t run right using a 100mA or 200mA DC power source. Weird, it seems to need more power then it should when it’s bypassing the battery.Please Help if you can.Thanks alot
hi all , i need the schematics of the electro harmonix memory man (no deluxe memory man).
many thanks !!!!!!!!!!
i need the schematic for the dod bass overdrive model fx-91. email me if you’ve got it/know where i can find it
This popular thread has been given its own page : Deluxe Memory Man missing MN3005?
i need of the circuit complet plese, thank you.
I have the schematic. Send me your email and one photo from your memory man inside ( the components view and the soldiers conections)
Thank you
Martin
I have the schematic. Send me your email and one photo from your memory man inside ( the components view and the soldiers conections)
Thank you
Martin
: Hello
:
: I have a 5 knob Deluxe Memory Man with MN3005’s. Now i just opened it up and had a look at a schematic, here is what i have noticed on the PCB board.
:
: 1. 2x MN3005 and one spare socket
: 2. 5x 4558
: 3. 1x NE570
: 4. 1x 5087
: 5. 5x Trim Pots
: 6. 1x 4047
:
: The MN3005’s are located on the top left of the PCB and the spare socket is the socket on the far left. And the two MN3005 are located to the right of that, under the three sockets are trim pots with a trim pot between the far right socket and the middle one
: Now i am assuming that there is one MN3005 missing??
:
: If anyone has a picture of the the PCB could you please post it, or even a schematic, i have look at one schematic but it had more NE570’s etc…
:
: Regards
It is just normal. EH have built somme Delay with a third MN3005 Socket but normal are 2 MN3005. Maybe you can but a third BBD Chip inside to enlarge your delay time up to 615ms.
Hello
I have a 5 knob Deluxe Memory Man with MN3005’s. Now i just opened it up and had a look at a schematic, here is what i have noticed on the PCB board.
1. 2x MN3005 and one spare socket
2. 5x 4558
3. 1x NE570
4. 1x 5087
5. 5x Trim Pots
6. 1x 4047
The MN3005’s are located on the top left of the PCB and the spare socket is the socket on the far left. And the two MN3005 are located to the right of that, under the three sockets are trim pots with a trim pot between the far right socket and the middle one
Now i am assuming that there is one MN3005 missing??
If anyone has a picture of the the PCB could you please post it, or even a schematic, i have look at one schematic but it had more NE570’s etc…
Regards
I need Schematics For the Dod Fx86 Death Metal Pedal. Mine Just took A crap! Can anyone help?
please send me schematics HELP ME
: please send me schematics HELP ME
: : please send me schematics HELP ME
: : : please send me schematics HELP ME
Do you still need a Dod fx67 stereo turbo chorus schematic? If so I can Email you a fairly decent one.
http://www.angelfire.com/bc2/electronics/schems/dodfx86.html
: http://www.angelfire.com/bc2/electronics/schems/dodfx86.html
: : http://www.angelfire.com/bc2/electronics/schems/dodfx86.html
http://www.republika.pl/kerry2/death.html
What’s the nFET’s name which is at the input of the schematic?
This isn’t the exact schematic, hope this helps
Cheers
http://resin.csoft.net/~stompbox/pedals/schems/DODfx-86.GIF
: I need Schematics For the Dod Fx86 Death Metal Pedal. Mine Just took A crap! Can anyone help?
angelfire site no complet,cresin.net not enter.Help
need scematic of boss or dod bass overdrive like boss ODB-3 , fx-91
This group discussion is dedicated to Pure Ambient Space Landscape Music.
To give Ambient Artist exposure due them and their music.
And to promote these talented artist and their Recording Label’s.
And to keep the fan’s in touch with the favorite artist e.g. (latest recordings, labels, concerts etc.). And allow there fans to speak out and discuss their ( artist ) music tracks and styles.
the_ambient_way-subscribe@yahoogroups
Rhea Cary Owner
Hope to hear from you. and please pass on the word to others who might be interested.
has been modified. need to put back to original
I need the Schematic for the digitech FS 300 Anyone who could help I would greatly appreciate
: I need the Schematic for the digitech FS 300 Anyone who could help I would greatly appreciate
http://www.plexusproductions.ca/fs300/
PLEASE I need a schematic Diagram for Wha Wha Effect CRYBaby.
Can you send it to me By e-mail ?
thanks !!!!!
Best Regards.
I am Italian.
What cry baby do you mean?GCB95?
I need a schemati for a eletronic bypass cicuit with led indicator effect on.
oi!
For switching, you’ve got many solution. Passive one, with switch, but not very easy and good look, and active. For active, you can use the 4066 CMOS chip. They are very cheap, try to get the
datasheet (easy to find), it’s 4 digital controled analog switch. Marshall in the VS100 use somme of them. But they’ve got bad dynamics. They are many version f this cheep, look for them. They are also
a way, like the Mesa V-Twin (www.scheamticsheaven.com) with FET, I never try this. And the last solutin, wich is most use in Mesa and rivera amp, it’s to use LDR. look at mesa dual rect!
I need the schematic of my Marshall VS100HR Head Amp, can you send it to me by e-mail.
Best Regards.
looking anywhere from 1 second and up if you have any please let me know..thankx
: looking anywhere from 1 second and up if you have any please let me know..thankx
: : looking anywhere from 1 second and up if you have any please let me know..thankx
: : : i’m needing this for my project!!! thanx…
: looking anywhere from 1 second and up if you have any please let me know..thankx
easy….
an ADC, DAC and memory…
A clock to make the whole thing work, and gooo!! Cheap!
If you want more, I’m working on a cheap multiFX processor… (so with very long delay, sampler!)
I need a Schematic Diagram for the Marshall VS100 Head.
Send to [email protected]
Thank you.
Hi. I need a schematic for a Marshall 8280 Bi-Chorus valvestate. Please contact me at [email protected]
thanks
if you got a schematic for the DOD DFX94 digital delay, let me know
thanks
I desperately need a schematic for an original Maxon D&S II distortion box. Or, better yet, can someone just tell me
where to reconnect the battery leads?
All help greatly appreciated.
Thanks,
Neil…
[email protected]
I really need a vs100r combo shematic pleaSee !!!!
🙂
thanks a lot!!
I need schematics of the following processar:
BOSS BOSS ME-10
I have one and I love the sound!
Thanks a lot!!
Hi. I’m looking for a Marshall Shred Master Schematic. Any help would be *greatly* appreciated.
: Hi. I’m looking for a Marshall Shred Master Schematic. Any help would be *greatly* appreciated.
: : Hi. I’m looking for a Marshall Shred Master Schematic. Any help would be *greatly* appreciated.
: : : Hi. I’m looking for a Marshall jcm 600 Schematic. Any help would be *greatly* appreciated.
: Hi. I’m looking for a Marshall Shred Master Schematic. Any help would be *greatly* appreciated.
I’ve got it, mail me if you want it!
hi,need the manual for the casio mg 510 midi guitar.Also,i’mlookin’for the schmatics of some enhancers,like the boss pedal or,better yet,the BBe stinger.Any help?thnks
: hi,need the manual for the casio mg 510 midi guitar.Also,i’mlookin’for the schmatics of some enhancers,like the boss pedal or,better yet,the BBe stinger.Any help?thnks
I just bought one of these, did you find a manual ?
My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
: My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
The tubes just need to warm up like every other tube product!!
This popular thread has been given its own page : Re: rocktron gainiac problem
: My gainiac sounds quite nice but after it warms up, the volume tapers off to a very weak signal. I replaced the 12ax7 and the problem remains. Changing power supply also did not help. Does anyone have a scematic or know about this problem in tube preamps?
I think it’s a problem of the power voltage.
If you have a voltmeter, plug it on the tube power, and see if when the sound go down the volatge go down. If it’s that, It may come in the power supply. Do you change it? or juste try? And what did you test? it may be a capacitor problem.
This popular thread has been given its own page : need H&K tubeman plus schematics
: I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
joerg
mrbill:
does anyone have hk schematics? I have an original tubeman and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
: hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
: joerg
: mrbill:
: does anyone have hk schematics? I have an original tubeman and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
: : hi, i just purchased a used tubeman plus. but without schematics? have you got a schematic???
: : joerg
: : mrbill:
: : does anyone have hk schematics? I have an original <b style="color:black;background-color:#ffff66">tubeman</b> and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : : I need Hughes & Kettner <b style="color:black;background-color:#ffff66">tubeman</b> <b style="color:black;background-color:#a0ffff">plus</b> schematics. Can anyone help me?
: : : hi, i just purchased a used <b style="color:black;background-color:#ffff66">tubeman</b> <b style="color:black;background-color:#a0ffff">plus</b>. but without schematics? have you got a schematic???
: : : joerg
: : mrbill:
: : does anyone have hk schematics? I have an original <b style="color:black;background-color:#a0ffff">tubeman</b> and wont part with it period. Having bounced it for the n’th time it needs more than a tube. I’ve been looking for schematics for a while and haven’t seen ANY hk schem’s for anything.
: : : I need Hughes & Kettner <b style="color:black;background-color:#a0ffff">tubeman</b> <b style="color:black;background-color:#99ff99">plus</b> schematics. Can anyone help me?
: : : hi, i just purchased a used <b style="color:black;background-color:#a0ffff">tubeman</b> <b style="color:black;background-color:#99ff99">plus</b>. but without schematics? have you got a schematic???
: : : joerg
Hi, did you found a schematic for your hk tubeman. If yes I’m interested in because i also own one and i would like to repair it.thank you.
I need Hughes & Kettner tubeman plus schematics. Can anyone help me?
I need a schematic for a Fender Sidekick amp Model SK 65 serial number 04557. Does anybody know where I can find one?
I have been recently hired in a repair shop that specializes in Guitar Amps…they have a bad backlog of vox amps and would like links files or help finding inexpensive schematics to help me catch up on the work…I appreciate all help in this matter
THANKS
Try the offical VOX homepage: voxamps.co.uk
you can find lots of amp- and effect-schematics when you search n the support and service area
Christoph
May I have if you have the OLD Vox Whawha Schematics ??
Thankss
?
Hey, I need schematics of the following effects: BOSS Metal Zone MT-2, BOSS OverDrive OD-3, BOSS Digital Delay DD-5 and BOSS Distorsion DS-1. As you can see´I´m a very big fan of the BOSS effects. Please if you can find them send them to me. Thanks a lot!!
Boss Metal Zone MT-2 MT2.zip (29kb)
http://www.mif.pg.gda.pl/homepages/tom/files/MT2.zip
and more
i also need schematics for the ds1 please email me
I HAVE A DIGITECH GSP 21 AND HAVE A PROBLEM WITH THE NOISE GATE. IF I TURN IT OFF IT STAYS ON AND CLIPS THE SIGNAL IF IT DOESNT REACH A CERTAIN LEVEL. IF ANYONE CAN HELP, PLEASE LET ME KNOW WHERE I CAN FIND A SCHEMATIC ON LINE OR HELP WITH MY PROBLEM.
Im having the same cliping problem.. anyone have a solution for it>?
If you have DIGITECH GSP-21 SCHEMATIC or oder effects
Send my please by e-mail [email protected]
I need scematics for a Kustom 11 BASS. Please Help
looking for any ibanez guitars in mid to late 70’s
This popular thread has been given its own page : Guitar Effects/Schematics
Hi! I’m looking for Boss ns-2 noise supressor.
Please, help me!
: Hi,
: I am trying to aquire a schematic on a deluxe big muff mine is broken.
: Please reply soon.
: Thankyou
Mine’s broken too, but maybe you could have a look at yours and tell me where the "hot" wire to the Comp socket comes from on the PCB – just tell me what component(s) share the track.
Here’s a few things you should check for:
15-0-15 Vac at the transformer secondary
+25 volts across the smoothing capacitor
check that the LED isn’t blown (it’s in SERIES with the Vcc line to the rest of the pedal – try shorting it out and see if your pedal comes to life).
Hi,
I am trying to aquire a schematic on a Digitech R.P. 2000 mine is broken.
Please reply soon.
Thankyou
HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
I have some rare EH schematics. Will trade for maxon pedal schematics. Email me
: HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
: : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shematic! Will we change?
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shenatic! Will we change?
: : : HI…I NEED SOME GUITAR EFFECTS I HAVE A GOOD COLLECTION OF THIS AND I WANT TO INTERCHANGE SCHEMATICS.thanks
Hi!
I have a lot of shenatic! Will we change?
Need schematic. Thanks.
: Need schematic. Thanks.
I need one as well for a midiverb 2. The overload light comes on on mine as soon as power is applied.
steve
: : Need schematic. Thanks.
: I need one as well for a midiverb 2. The overload light comes on on mine as soon as power is applied.
: steve
Same problem here. Did anybody receive an answer or the demanded circuit diagram ??
Thanks jojo
Hi, I also need a schematic of a Midiverb II. Same failure, the OVLD Led is on permanentely.
Thanks in advance
Hi, I also need a schematic of a Midiverb II. Same failure, the OVLD and Signal Led is on permanentely.
Thanks
hello,
schematic -delay,reverve,flanger,chorus.
: hello,
: schematic -delay,reverve,flanger,chorus.
Built a multiFX….
I’m working on it, with PC board and embeded Linux… cheap, and very good… soon a website on it, mail me if you want more!
I scored one for 5 bucks, but cant get the infinite loop to work (LED doesn’t light, no effect). Anyone know possible cause offhand, or could point me towards a schematic? Thanks!
hey if you get the schematic drop me aline i could use one also….thanks
I need a shematic for a jimi hendrix (jim dunlop)wha wha, model jh-1.
I want to increase the low end frequancy response and need to know what caps i need to change out……….thanks , Ray
I am looking for an effect switcher schematic;passive is ok or active
is alright .It would be used to switch multiple effects in and out ,and to
switch to multiple amps.I would like to learn to do it like the pro’s do.
Any help would be greatly appreciated.
charles phillips [email protected]
rock on
: I am looking for an effect switcher schematic;passive is ok or active
: is alright .It would be used to switch multiple effects in and out ,and to
: switch to multiple amps.I would like to learn to do it like the pro’s do.
: Any help would be greatly appreciated.
: charles phillips [email protected]
: rock on
oi!
For switching, you’ve got many solution. Passive one, with switch, but not very easy and good look, and active. For active, you can use the 4066 CMOS chip. They are very cheap, try to get the datasheet (easy to find), it’s 4 digital controled analog switch. Marshall in the VS100 use somme of them. But they’ve got bad dynamics. They are many version f this cheep, look for them. They are also a way, like the Mesa V-Twin (www.scheamticsheaven.com) with FET, I never try this. And the last solutin, wich is most use in Mesa and rivera amp, it’s to use LDR. look at mesa dual rect!
HI I IM A GUITAR EFFECTS DESIGNER,I WANNT TO CHANGE SCHEMATICS AND IDEAS …
I NEED A LOT OF COMPRESSOR SCHEMATICS…PLEASE SEND ME …
THANKS
could use one of these if anyones got one
Hi. I also could use one of these if anyones got one
: I need this schematic too, where can I get it?, thanks,
JM
I need this schematic. Thank You.Can You give me a geral schematic index?How much?
i need a schematic for a digitech 2112/2120
i need deluxe memory man schematics! can anyone help?
I’m looking for schematic diagram for 15W Crate guitar amplifier with overdrive .
Thanks
I’m looking for schematic for Ibanez overdrive OD-850 (orange). Thank you very much
: I’m looking for schematic for Ibanez overdrive OD-850 (orange). Thank you very much
Did you get schematic for od-850, i need too.
I need scematics for Marshall JCM900 combo